Woodworking Equipment For Sale

WYSONG & MILES - 315, ...Edge Sander6" x 32" Graphite mocovered wooden platen; double 8" x 34" tilting side tables; full 180° steel end table; tilts and raises & lowers. -- 2 HP Motor; direct drive motor.

Used YAMAMOTO 30-opening, premium quality, Plywood Hot Press. -- 500 Tons pressing capacity. -- Daylight is 4.7"(120mm). -- Press plates are 54" x 108" x 1.5" (1,370 x 2,700 x 40 mm). -- Auto loader feeds charger using pusher arm to load press. -- Pie rack with automatic unloader. -- Hydraulic system with accumulation tank. -- Heated by steam. -- Professional removal and loading available at Buyer's cost.

Used YAMAMOTO 45-opening, premium quality, Plywood Hot Press. -- 500 Tons Pressure Capacity. -- Daylight is 2.75" (70 mm). -- Press Platens are 106" x 53" x 1.57" (2,700 x 1,350 x 40 mm). -- Auto loader feeds charger using pusher arm to load press. -- Pie rack with automatic unloader. -- Hydraulic system with accumulation tank. -- Heated by steam. -- This particular press was only operated for about 1-1/2 years. -- Professional removal and loading available at Buyer's cost.

Yaskawa Motoman UP50N Robot YR-UP50N-A00 Payload 50kg Control Box Teach Pendant Yaskawa Motoman UP50N Robot Type: YR-UP50N-A00 Payload 50kg

Yates A20-12 Planer Infeed Deck Tilt Hoist 575 V Includes: Misc parts, heads and attachments for S4S and T&G. This system was removed from service this Spring. It is ready to load.

There are two of these systems available. They were recently removed from the current operation and available immediately.

Yates-American A-20 planer. 4 sided with profile machine, 10" rolls. Includes 10 cylinder Detroit engine, belt drive assembly.

The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

Yates American B-15 Helical Head Planer S/N 29658

Used Yates American Model B-26, 24” Double Planer, 75HP top, 40HPBottom, top and bottom 10 knife cutterheads, on the fly top and bottom jointers, 3 phase 480volt electrics, slide out lower cutterhead, top fixed cutterhead, 3-3/4” thickness capacity, approx. 20HP hydraulic feed works, power bed raise and lower, sectional pneumatic chip breaker, top infeed/outfeed rubber rollers.

Yates American E-12 End Matcher System for tongue and groove flooring includes: Belt, Straight Line Blade, 3-blades, Infeed conveyor to end matcher, transfer conveyor from first machine to second machine, variable speed outfeed conveyor

Planer Head Set Up Stand

YATES AMERICAN B-26 Top & Bottom Rough Lumber Planer24" x 4" Opening cap., 3/4" to 4" thickness capacity; 46" minimum unbutted length capacity;Specifications: -- (1) 75 HP DMD motor power hoisted top head, (1) 40 HP DMD motor bottom head, 8" dia. cutting circle at 3,450 RPM. -- 40 HP Hydraulic power unit for variable feed rate from 75 to 400 FPM, 12" dia. Urethane tire top feed rolls, 12" dia. non-powered lower rolls. Equipped with: -- Carbide spiral cutterheads, automatic pressure bar release (hydraulically operated), hydraulic top & bottom headlocks, anti-lap bar device, air tensioned & released chipbreaker. -- Complete with: Built-in top & bottom jointers, dust hoods, electrically interlocked safety guards, and small remote operator's console.

Setup stand, good condition

220v 3 phase 2hp motor Controls work, motor runs and spindle turns Spindle raising mechanism has pin sheared in bevel gear. Includes overarm casting & mobile base.

ZANGHERI & BOSCHETTI B-35 CONSTRUCTION/LINE BORER(35) Spindles, 4 HP motor, drills vertically from the bottom/ horizontally from the back, 45° bevel drilling feature; (6) pneumatic holddown clamps for vertical & horizontal clamping, includes fences & stops. -- The 56" x 30" table shifts when changing from horizontal to vertical maintaining same boring depth and zero base. Removable table fence for extended length line boring.

ZEETECH - 200, ...Universal Hopper Feeder that can be mounted to all Moulders. - Capacity: 3/4" - 9-1/2" width, 0.38" - 5" max. material height, 10" min. length. -- Oil-free air operated drive unit mounted on THOMPSON hardened ways, damped drive travel, positive sensing sequencing actuator. -- Variable speed range from 0 - 120 FPM @ 80 - 120 PSI. -- Includes: All air logic controls (no power required) and air filters; easy to install.

ZUCKERMANN CHALLENGER 1700 37-Z SYNCHRO Copy Lathe. Single spindle hopper feed CNC Copy Lathe for shaping & sanding asymmetrical parts. -- Size Capacity: 67" Maximum 67" (1700mm) and 4" (100mm) minimum working length, 9.8" maximum working diameter. -- Drives/Speeds: The cutter head is belt driven by 5.5 HP motor to run at 6,000 RPM, sanding motor 1.5 HP to drive a 5-7/8" wide sanding belt. Work piece rotation CNC controlled for variable rate from 12 - 130 RPM, via 4 HP motor, carriage speed CNC controlled 7- 67 inches per minute, automatic hopper feed as well as automatic unloading . -- Controls: Machine sequencing, cutting and sanding speeds controlled by SIEMENS "Sinumerik 810 T" CNC controller with programmable memory for rapid set up. --Complete with: Various spare parts & 220 or 440 V operation transformer.

ZUCKERMANN OPTIMA-S-8/1000 Copy Lathe with integral sanding.For asymmetrical or symmetrical wood turnings ranging from furniture legs (Queen Anne), gunstocks, guitar necks, to tool handles and the like. -- General Specs: 8-Spindle Copy Lathe, 39.3" (1000 mm) max. copying length, max. working dia. 200 mm (7.86"); 5.5 HP motor on each spindle, 6,000 RPM belt-driven spindle with cup cutters. All cutters are copying according to one sample specimen. -- Equipped with: (8) Single head sanders for simultaneously shaping & sanding; (2) 2.8 HP motors power all sanding heads, 6" wide sanding belts. -- Speeds: Stock rotation variable from 15 - 75 RPM, variable feed speed of shaping & sanding cycle from 200 mm/Min - to 1,200 mm/Min (0.75 IPM to 47 IPM), pneumatic clamping of workpiece. Includes: Installed used cup cutter heads. -- Larger working dia. is possible by omitting adjacent workpieces and as the copier allows. -- Actual model is OPTIMA-S-8/1000. -- Machines are connected and can be viewed in operation. --NOTE: Several machines of the same model are available at the same location.