This listing Is for a complete line that consists of a Flow Coating line that feeds into a cross transfer oven and back out on to an outfeed conveyor making a 180 degree circuit. The heat exchanger needs to be heated by means of a hot water boiler or similar. Maximum Part width: 305 mmSpeed range: 2 - 10 m/min.Pos. 1 - FEEDING BELT CONVEYOR:For feeding the batches into the flowcoater, Belt with marked area to built a gap for the angle transfer, Technical Data: length: 2300 mmPos. 2 - IMPREGNATION MACHINE VEN FLOW:For flowcoating of profiles in continious production with a waterbased impregnation (viscosity similar to water)The material is is sprinkled on the surface and remains for appr. 10 seconds. After this time a high pressure air knife nozzles will blow the acess materialfrom the surface. The whole cabin is built with fall to the side to collect the rest of the material. It is reused after passing a filter system. The cabin is built of stainless steel. The blowing off of the access material by air knife is effected by a high pressure fan.The machine comprises:1 conveyor system with spray protected roller system length 3000 mm1 sprinkling zone with two nozzle systems adjusted to reach the whole surface of the workpiece. length: 200 mm1 penetration area length ca. 1000 mm time of residence ca. 10 sec1 blowing zone with adjustable knife nozzles air supply with high pressure fan air flow adjustable by frequency converter length ca. 1000 mmair speed ca. 40 m/sec. material supply to supply the two sprinklers with fluid and collector for recovered material.workpiece tolerances:twist: max. 1° on the whole length, straightness max. 0,5mm deviation/m in horizontal and vertical weight distribution: evenly on whole length coating material: waterbased impregnation. Unstable components can not be repositioned when tilted.Pos. 3 - MOULDING ANGLE TRANSFER VEN TRANS 90°conveying from lengthwise direction to crosswise, comprising:1 excenter-transfer arms integrated into the driven infeef roller conveyor. The tacted transfer system allows a minimum distance between the singlemouldings on the following cross transfer system.Technical Data:length of roller conveyor: 4500 mmroller pitch: 185 mmnumber of transfer arms: 22spacing 185 mmtacting cycle: max. 30/min.Pos. 4 - MOULDING CROSSWISE V-BELT CONVEYOR:Mouldings are conveyed by means of various v-belts along the system. The unit is fitted with an insulation cover between the conveyor. A drying tunnel is fitted on top of the unit.Technical data:length: 4000 mmoperating width: 4200 mmnumber of belts: 22distance of belts: 185 mmoutfeed prepared for an additional angletransfer:position of driving shaft in the middlegaps for passing of the carriers of the angle transferPos. 5 - JET DRYING TUNNEL 70 °C:Made of sandwich elements with fire preventing insulation material. The even distribution of air over the full operating width is reached by using slot nozzles on the full width of the tunnel. One combined heating-, fan

VERVILLE VP424-S-CCW BAGGING SYSTEM4-Station Compression Bagging SystemSpecifications & Includes: -- High Tubes of 116" -- Bag Size 11" x17" up to 30" High -- Automatic Plastic Bag Sealer -- Oil Tank Heater and Modem -- Supplied with Transformer for your VoltageLoaded on your Truck

VERVILLE 6-SCREW HOLDING BINSpecifications: -- (6) Motorized 14-1/2" Diameter Bottom Screw -- (1) Motorized 14-1/2" Diameter Exit Screw -- 11 Feet Long -- 16 Feet Wide -- 18 Feet High -- 12 Feet High Support LegsDismantled and Loaded on Truck

VERVILLE VP300 3-Station Bagging SystemSpecifications: -- Main motor: 25 HP -- High of Tubes 116" -- Bag Size 11" x 17" x Up to 30" Finish HighNote: Bin and Infeed auger/conveyor is not included.

ZAFFARONI MLS 130 P PD MULTI-BLADE PANEL SAW: -- SpecificationsZaffaroni is the Top of the Line in Precision Multi Rip saws for Panels. Blade Depth is mechanically adjustable with a tolerance of =- 0.01 mm (0.0004"). The saw is so precise it can also be used for "V" grooving.The Saw blades project through the table from below. A double row of hold down wheels are mounted above the saw, with 24 adjustable rollers to prevent contact with the blade.Technical Characteristics: -- Working Width 1300 mm (51-1/8") -- Min. Panel Length 300 mm (11-7/8"). -- Motorized thickness adjustment from 0 - 70 mm (2-3/4"). -- Adjustable projection of the saw blades from the working from 42 - 62 mm (1- 5/8" - 2-7/16") with circular saw blades or hogger trimmer up to 280 mm diam. (11"). -- Working Table Height 1120 mm (44"). -- Transport Speed from 3 - 45 MPM (9.8 - 147.6 FPM). -- Main Motor Power 37 KW (50 HP) with Belt Drive. -- Saw Blade Spindle 80 mm x 1310 mm (3-1/8: x 51-1/2"), with double tangs and automatic anti-rotation locking clutch. -- Spindle Speed 4,000 RPM.Machine Features: -- Opening of the roller group through pneumatic cylinder with timer interlock for safety. -- Safety protection hood with sound absorbing materials to conform to ISO 7960/95 Norm. -- PLC logic control with digtital communications through bus cable.Spacer Sets: Machines require Spacer Sets and Saw Blades (not included) and pricing is available on request.

ZAFFARONI MLS 160 P MULTI-BLADE PANEL SAW: -- SpecificationsZAFFARONI is the "Top of the Line" in Precision Multi-Rip Saws for Panels. Blade Depth is mechanically adjustable with a tolerance of +/- 0.01 mm (0.0004"). The Saw is so precise it can also be used for V-Grooving.The Saw blades project through the table from below. A double-row of hold-down wheels are mounted above the Saw, with (24) adjustable rollers to prevent contact with the blade.Technical Characteristics: -- Working Width is 1,600 mm (63"). -- Max. panel pass through is 1,780 mm (70"), min. length is (320 mm) 12-5/8". -- Motorized thickness adjustment from 0 - 70 mm (2-3/4"). -- Adjustable projection of the saw blades from the working from 42 - 62 mm (1-5/8" - 2-7/16") with circular saw blades or hogger trimmer up to 280 mm dia. (11"). -- Working table height is 1,120 mm (44"). -- Material Feed Speed from 3 - 45 MPM (9.8 - 147.6 FPM). -- Main Motor Power is 55 kW (74 HP) with Belt Drive arbor. -- Saw Blade arbor 80 mm dia. x 1,310 mm (3-1/8" x 51-1/2"), with double-tangs and automatic anti-rotation locking clutch. -- Blade Arbor Speed of 4,000 RPM.Machine Features: -- Opening of the roller group through pneumatic cylinder with timer interlock for safety. -- Safety protection hood with sound absorbing materials to conform to ISO 7960/95 Norm. -- PLC Logic control with digital communications through bus cable.Spacer Sets: Machine requires Spacer Sets and Saw Blades (not included); pricing is available on request. Examples:width from......1 - 10 mm ...$ 25.45width from.....11 - 25 mm ...$ 30.15width from.....26 - 50 mm ...$ 35.60width from.....51 - 75 mm ...$ 40.15width from.....76 - 100 mm ...$ 45.20width from...101 - 125 mm ...$ 49.75width from...126 - 150 mm ...$ 54.90

ZAFFARONI MSR 160 P BS/PD MULTI-BLADE PANEL SAW (W/TOP & BOTTOM ARBORS): -- SpecificationsZAFFARONI is the "Top of the Line" in Precision Multi-Rip Saws for Panels. Blade Depth is mechanically adjustable with a tolerance of +/- 0.01 mm (0.0004").The Saw is so precise it can also be used for V-Grooving.The Saw blades project through the table from above & below. A double-row of hold-down wheels are mounted above the saw, with (28) adjustable rollers to prevent contact with the blade.The Top & Bottom shafts & wheels are connected by a quick flange system that can be removed/replaced without dismounting the bearing collars.Motorized adjustment of the depth of the saw blade projection by the touch-screen operating control(4) motorized & self-adjusting (according to material thickness) upper rubber coated rollers with grooves,(4) Idle lower polyethylene coated rollers & (1) Pair of ejector rollers at the output of the machine.Automatic locking and unlocking arbor shaft with HSK collector on the LH side controlled with electro-pneumatic device for the automatic cleaning of the coupling Safety device that features a presence and positioning sensor of the shaft; closed circuit air cooling device for the shaft bearingsSaw Blade work table with interchangeable MDF inserts.Technical Characteristics: -- Working Width is 1,600 mm (63"). -- Max. panel pass through is 1,780 mm (70"), min. length is (450 mm) 17.7". -- Motorized thickness adjustment from 0 - 70 mm (2.7"). -- Adjustable projection of the saw blades from the working from 0 - 62 mm (0" - 2.4") with circular saw blades or hogger trimmer up to 280 mm dia. (11"). -- Working table height is variable, from 970 - 1270 mm (38" - 50"). -- Material Feed Speed from 3 - 45 MPM (9.8 - 147.6 FPM). -- Main Motor Power is 45 kW (60 HP) with toothed Belt Drive arbor. -- Saw Blade arbor 80 mm dia. x 1,310 mm (3-1/8" x 51-1/2"), with double-tangs and automatic anti-rotation locking clutch. -- Blade Arbor Speed of 4,000 RPM.Machine Features: -- Opening of the roller group through pneumatic cylinder with timer interlock for safety. -- Safety protection hood with sound absorbing materials to conform to ISO 7960/95 Norm. -- PLC Logic touch screen control with digital communications through profibus cable.Spacer Sets: Machine requires Spacer Sets and Saw Blades (not included); pricing is available on request.Examples:width from......1 - 10 mm ...$ 25.45width from.....11 - 25 mm ...$ 30.15width from.....26 - 50 mm ...$ 35.60width from.....51 - 75 mm ...$ 40.15width from.....76 - 100 mm ...$ 45.20width from...101 - 125 mm ...$ 49.75width from...126 - 150 mm ...$ 54.90Example of productivity:Approx. 240 panels/hour running the machine at 49 FPM (15MPM) – considering to load 4 panels/minute) & a change-over time of approx. 10 minutes.

ZANGHERI & BOSCHETTI B-35 CONSTRUCTION/LINE BORER(35) Spindles, 4 HP motor, drills vertically from the bottom/ horizontally from the back, 45° bevel drilling feature; (6) pneumatic holddown clamps for vertical & horizontal clamping, includes fences & stops. -- The 56" x 30" table shifts when changing from horizontal to vertical maintaining same boring depth and zero base. Removable table fence for extended length line boring.

ZEETECH - 200, ...Universal Hopper Feeder that can be mounted to all Moulders. - Capacity: 3/4" - 9-1/2" width, 0.38" - 5" max. material height, 10" min. length. -- Oil-free air operated drive unit mounted on THOMPSON hardened ways, damped drive travel, positive sensing sequencing actuator. -- Variable speed range from 0 - 120 FPM @ 80 - 120 PSI. -- Includes: All air logic controls (no power required) and air filters; easy to install.

MODEL ZTLP 1800 X 1600 Zeno Low Noise Single Shaft Shredder/Chipper Specifications: --Model ZTLP 1800 X 1600 -- Feed opening 70’’ (1800mm) wide x approximately 62’’ (1600mm) long. --24’’ Diameter x 70’’ long single rotor with bolt-on blades. --Hydraulic pusher ram feed. --Shredder driven by a 105 kW (140 hp) --3/60/460 volt --1780 rpm motor --No Control Panel --New in 2005

ZUCKERMANN CHALLEGER Copy Lathe w/Sander for asymmetric/irregular shaped parts.Hopper feed, single spindle; approx. 149" (3,800 mm) max. between centers, 8-13/16" (250 mm) max. part dia.; 5 HP cutter head motor at 6,000 RPM, oscillating belt sanding unit, both units work together. -- 'Cup' style Cutter head; 2 HP spindle & pattern rotation motor; mechanical & pneumatic traverse of cutter head and sanding carriage. -- Complete with: Built-in operator push button control panel and overhead dust collector hood.

ZUCKERMANN CHALLENGER 1700 37-Z SYNCHRO Copy Lathe. Single spindle hopper feed CNC Copy Lathe for shaping & sanding asymmetrical parts. -- Size Capacity: 67" Maximum 67" (1700mm) and 4" (100mm) minimum working length, 9.8" maximum working diameter. -- Drives/Speeds: The cutter head is belt driven by 5.5 HP motor to run at 6,000 RPM, sanding motor 1.5 HP to drive a 5-7/8" wide sanding belt. Work piece rotation CNC controlled for variable rate from 12 - 130 RPM, via 4 HP motor, carriage speed CNC controlled 7- 67 inches per minute, automatic hopper feed as well as automatic unloading . -- Controls: Machine sequencing, cutting and sanding speeds controlled by SIEMENS "Sinumerik 810 T" CNC controller with programmable memory for rapid set up. --Complete with: Various spare parts & 220 or 440 V operation transformer.

ZUCKERMANN OPTIMA-S-8/1000 Copy Lathe with integral sanding.For asymmetrical or symmetrical wood turnings ranging from furniture legs (Queen Anne), gunstocks, guitar necks, to tool handles and the like. -- General Specs: 8-Spindle Copy Lathe, 39.3" (1000 mm) max. copying length, max. working dia. 200 mm (7.86"); 5.5 HP motor on each spindle, 6,000 RPM belt-driven spindle with cup cutters. All cutters are copying according to one sample specimen. -- Equipped with: (8) Single head sanders for simultaneously shaping & sanding; (2) 2.8 HP motors power all sanding heads, 6" wide sanding belts. -- Speeds: Stock rotation variable from 15 - 75 RPM, variable feed speed of shaping & sanding cycle from 200 mm/Min - to 1,200 mm/Min (0.75 IPM to 47 IPM), pneumatic clamping of workpiece. Includes: Installed used cup cutter heads. -- Larger working dia. is possible by omitting adjacent workpieces and as the copier allows. -- Actual model is OPTIMA-S-8/1000. -- Machines are connected and can be viewed in operation. --NOTE: Several machines of the same model are available at the same location.