CANTEK C-14RS Straight Line Rip Saw; Absolute straight line feeding Rip Saw. Rigid machine body consists of a thick welded steel frame with an integral table which is fitted with a sturdy cast column. Excellent precision work accuracy and durability.Specifications: -- 4.92" Max. thickness cap; 8" min. length; variable feed speeds from 50 to 120 FPM and powered by a 1 HP feed motor. -- 1" Dia. saw arbor powered by 20 HP arbor motor; swings 12" thru 16" dia. blade at 4,500 RPM; with 24" distance from blade to saw column. -- 31-7/8" From floor to top of table; table is 50" wide x 75" long.Feed System & Chain: -- Precision caterpillar chain and double "VEE" guide rails are made of special cast iron. The chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Hold-down rolls for increased control and precise straight line cutting (6 rows). -- Mechanical operation Chain Oiler (Best) provides consistent lubrication to the chain track and automatically adjusts to your feed speed. When oil runs out the machine track stops running to avoid damage to track. Features: -- Precision Built Saw Arbor constructed of nickel chrome steel, large diameter, accurately ground and dynamically balanced. The arbor runs in precision angular contact type ball bearings (eliminates any radial run-out & axial thrust) - V-Belt driven from below, with easy to access adjustments and controls. -- (3) Sets of anti-kickback fingers; (2) top and (1) set in the table. -- Soft start - Star Delta starter. Telemecanique U/L magnetic starters.Options available at additional cost: -- 20mW Red Laser (FPIMLC1320WFL) & Laser Holder (FPICAN03)..................................... $ 495.00 -- Extra Saw Blade: 14";x0.157"; kerf x 1.5"; bore x 60T (CANC14RS-BLADE-14)........... $ 118.00

CANTEK MX350 EDGEBANDER (W/ PRE-MILLING): -- Specifications:0.4-3 mm Edge thickness, panel thickness 8~45 mm, min. panel width 100 mm (4″), min. panel length 170 mm (6.7″). Equipped with: -- Quick melt Teflon coated glue pot 2.5 Lb capacity. Two spring loaded pressure rollers (One driven, one idling). Automatic coil feed PVC/ABS up to 3mm thick, pneumatically operated guillotine. Laminate strip material can be hand-fed. PLC control system with LED display and keypadWorkstations: -- Pre-Mill station with (2) 1.1 Kw 12,000 RPM trim motors 32 mm (1.25") max. material thickness. -- Single motor front and rear edge trim station. -- Top & bottom trim station with insert knife cutters for radius trimming & bevel trimming. -- Top & bottom scrape station 2 mm radius. -- Top & bottom buffing. -- Feed speed 29 FPM

CANTEK MX-370P EDGEBANDER (W/ PRE-MILL & CORNER ROUNDING): --Specifications:0.4 - 3 mm Edge thickness, panel thickness 0.315" - 1.77". Minimum panel length 6.7", minimum panel width 3-¾". Heated infeed fence for better glue adhesion. Fixed feed speed 29 FPM.Equipped with: -- Pre-mill (2) 1.5 kW each (12,000 RPM) counter-rotating cutter-heads for removing up to 3mm of the panel edge. -- Quick change 1.2 kg Teflon-coated glue pot is designed for EVA hot-melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than 1 minute. -- Guillotine shear: The guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consist of one large driven roller, followed by a smaller one. Workstations: -- End Trim: The end trim system is a single motor with (2) saw blades. The unit is mounted on high-precision linear guide rails. -- Top & bottom trimmers with (2) high-frequency motors for top & bottom trimming of the panel. Each motor has an inset knife cutter-head which can be adjusted from flush to beveled finish for thin edges, and radius trimming (2 mm radius). Single motor Corner Rounding Unit Can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm). The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Radius scraping unit fine-tunes the edge radius while removing knife marks during the milling process on radius edging. Insert knives have a 2 mm radius. -- Buffing unit leaves a super finish on ABS and PVC edging and removes any discoloration on the edges.

CANTEK MX340M Edgebander (Single Phase):The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- Equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thiknesses of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.Also available in 220V/3PH/ 60 Hz

CANTEK MODEL CFS100 / EM-12 DEFECT SAW AND END-MATCHING SYSTEM:Consisting of a CANTEK model "CFS-100" Optimizing Cut-Off Saw followed by a CANTEK Model "EM 12" Through-Feed End Matcher and with the following specifications and features: CANTEK "CFS-100" OPTIMIZING CUT-OFF SAW -- Up to 20 mm X 200 mm or 100 mm X 100 mm( 3/4" X 7.87" or 3.9" X 3.9" cutting capacity with 18" x 30 mm bore sawblade is driven by a 10 HP motor driving the saw spindle at 3,200 RPM; 2.7 HP servo drive feed system drives the stock up to 260 FPM; 0.787" min. distance between crayon marks; requires 75 to 80 PSI at the saw and 100 to 120 PSI at defect blow-off station. Machine comes completely wired and programmed. -- Machine is ideal for separating crayon marked waste zones from useable material before entering into a feed-thru End Matcher; provides (3) times greater production than manual cut-off saws.5% + Material recovery (yield increase) over manual cutting; compact and user-friendly design; controller adopts an industrial grade computer that employs a 32-bit floating-point DSP system and features flash and battery backup SRAM for double security; superior to conventional PC-based controls, it can fully eliminate the machine going down or being damaged due to a poor environment, such as, unstable voltage, high temperature, sawdust, etc. -- With defect blow-off system combined with computerized logic control permits the blow-off time and the length of defect to be set as desired; provides efficient defect removal and eliminates defects from bumping against the sawblade, resulting in the machine going down or sawblade damage. -- Computer control provides easy and fast maintenance; feed system driven by a servo motor for fast and accurate motion and position control; max. feed speed up to 260 FPM; cutting rate up to 80 cuts per minute with cutting accuracy within approx. ±1mm / 0.40"; control employs a touch screen for easy learning and operation.Features: -- New machine design features maximum maintenance convenience; high quality electric components provide maximum dependability; safety guards for maximum operator protection; 48" long infeed table standard - longer available option; 18" carbide blade included.(5) Cutting modes include: -- Adjustable end cuts to a max. of 10mm (0.4") -- Fixed length of cutting mode. -- Sequential cutting mode with (10) sets of cutting sizes held in memory (for sequential cutting mode only). -- Cutting on fluorescent marks with double-end trimming (perfect solution for end matching). -- Reading fluorescent marks with double end trim, fixed-length, random length end match, and finger joint block cutting. CANTEK "EM-12" END MATCHER -- Continuous through-feed system; handles random length min. 10.6" to any length x 0.4" to 1.38" thickness x 12" width capacity; -- 295 FPM max. feed speed; average speed of 75 FPM based on 6'-6" board lengths; with 118" infeed and 98" outfeed tables; -- 5.5 HP Shaper motors, 1 HP feed motor an

D M C - UNISAND 135, ...3-Head Wide Belt Veneer & Finishing Sander. -- General Data:3-Head, 51" (1,300 mm) nominal width cap.; motorized part thickness opening with LED readout; 1/8" to 4" max. - Head sequence: Cross belt, rubber-covered Drum, Pad. Head Configuration/Specs: -- 1st Head: Cross belt with: EPICS 44 Segmented electronically controlled air platen; 2-speed abrasive belt; approx. 36/72 FPM (11/22 MPS) linear speed; driven by 19 & 24 HP motors; 6" wide x 238" (6,050 mm) long abrasive belt. Inside synchronized Chevron belt, approx. 228" (5,800 mm) long.Pad unit with pneumatic cylinders: Each acting on a high absorption felt strip; working pressure controlled via control panel. HYDRA Belt: 2' Electronic control with oscillating blower for cleaning. -- 2nd Head: Rubber-covered 45-durometer steel roll, 9.8" (250 mm) dia. with: 18 HP 2-speed motor, 52" x 103" (4,055 mm) long oscillating abrasive belt with electronic tracking; air blast abrasive belt cleaner. Belt runs approx. 3,550 FPM (18 MPS) linear speed; adjustment & indicator of working position. -- 3rd Head: Flexible Sanding Platen with: EPICS 44 Segmented electronically controlled air platens; 3-speed 24 HP motors; 52" x 103" (4,055 MM) long abrasive oscillating belt with electronic tracking, timed oscillating air blast abrasive belt cleaner.Pad unit composed of: Pneumatic cylinders, each acting on a high absorption felt strip. Working pressure controlled vial control panel. Special rails allowing a quick change of graphite cloth on pad. Interchangeable system to modify the hardness, stiffness, and profile of the contact surface. Controller: -- DMC "HYDRA 30" Upgraded computer with: Working position display modes mounted in a separate control cabinet; automatic thickness device reads and adjusts feet table height, motor load meters. Transport Belt Drive: -- Variable feed speed of 16 to 82 FPM, conveyor feed drive, infeed & outfeed holddown pinch rolls on all heads; infeed hand safety stop, outfeed emergency stop; high efficiency dust extraction and separate control console with monitor, keypad, etc. Also included: -- Cleaning brush head at machine discharge. -- High pressure vacuum blower. -- Dust manifold. -- Extended outfeed table.

DMC UNISAND K 1100 Wide belt sander4-Head, 43" (1,100 mm) max. width cap. Head sequence: (3) Contact rolls and (1) Combi with roller and segmented platen.Heads configuration: -- 1st Head: Helical grooved steel contact roll, 10" dia., 48 HP motor. -- 2nd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. and 65-Shore covering hardness, 35 HP motor. -- 3rd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. 45-Shore covering hardness, 30 HP motor. -- 4th Head: Combi head with roller covered with rubber, 30 shore and Finishing sanding pad unit , 30 HP 2-speed motor with segmented pads pneumatically controlled -- All heads use 44" x 103" (to be confirmed) abrasive belts and are equipped with electronic tracking, automatic tensioning, automatic emergency breaking, and oscillating sanding belt cleaners.Controls: -- "HYDRA V-PAD" 10" Touch-screen computer for setup functions, color LCD Display, allows operator to setup/recall part thickness, -- Conveyor feed speed (3.5 - 18 MPM), -- Abrasive belt direction, and reversible speed setting of 4th head. -- Conveyor belt feed with inverter control, feed speeds from 11 - 60 FPM, 5.5 HP feed drive; -- Infeed & outfeed holddown pinch rolls on all heads, automatic part thickness setup with the moving feed belt, -- 2-speed motorized part thickness adjustment, 1/8" - 6" max. opening; -- Infeed & outfeed motorized conveyor extension rollers, automatic part thickness setup sensor. Complete with: -- Safety stop at infeed, -- Anti-kickback device, -- Infeed & outfeed emergency stops, -- Motor load meters, i -- Infeed & outfeed idle rollers, -- High efficiency dust extraction, and control console with monitor.Note: (spare parts not installed) New feed belt , new front pressure roller, new front pressure bar and several new small parts for approx $15,000 of value +11 boxes (approx 5 belts/ box) sanding belts 100 grit, 120 grit, 180 grit and 220 grit.

SCM DMC 90 RCS 135 2 Head 53 inch Wide Belt Sander 53" Width cap, Steel Drum, Combination HeadHead configuration1st Head: Steel Drum 36 HP Motor, 9" Diameter 2nd Head: Combination head 65 shore drum and solid wood platen, 30 HP Motor, 7" Dia. drumSpecifications: -- 54" x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computer controlled; set-up functions with a keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, -- Motor load meters. -- 2-Roll infeed conveyor extension; -- High-efficiency dust extraction.NOTE: Specs have to be verified

D M C FINESAND 130 2PO WIDE BELT (50" - 90", 2-HEAD): -- Specifications:Orbital Pad Sander, designed for cross-grain scratch removal on style & rail frames; with (2) Orbital Platens & (1) Brush. -- Working Capacity: Width 51", height/opening 1/8" - 4-5/8", motorized part thickness adjustment with digital readout, (4) screw jacks rise & fall. -- Sanding Heads: (2) 10" Wide Platen heads with rubber surface for elimination of abrasive belt cross-grain scratches. Dual orbital action heads with (1) high speed orbit on sanding pad, powered by 5.5 HP motor, and a secondary "low RPM" orbit on head assembly (1.5 HP motor), superimposed over the high-speed orbit for fast cutting action. -- Rotating Cleaning brush on outfeed side. Abrasive material for Sanding Heads is 18" x 52" in size. -- Feed Conveyor: Variable feed speed from 6 - 40 FPM, inverter controlled by 5.5 HP motor; vacuum conveyor bed with 15 HP blower motor. -- Complete With: - Digital height readout. - Infeed and outfeed rubber coated hold-down rolls. - Infeed hand safety stop bar, emergency e-stop. - Star-Delta motor starter. - (2) Dial indicator motor load meters.

DMCTC 1350-M2-RP Orbital Sander (2) Heads --53" Width cap. Drum, Combination Head --Head Configuration --1st Head:10" Dia. helical grooved rubber covered calibrating roller, 26 kw (34 HP) motor. --2nd Head: Rubber covered contact roller with finishing platen 18 kw ( 28.5 HP) motor. --Specifications --Working width 1350 mm --Max thickness 170 mm --Belt size both heads 1370 mm X 2620 mm --Feed speeds variable from 3.5 -18 m/min. Feed motor 2.2 kw ( 3 HP) motor --Equipped With --Electronic sanding belt oscillation --Exhaust hoods with 4 outlets --Motor safety switch for main motor --Power rise and fall --Panel cleaning brush --Sander dim. L 2600 mm X W 2400 mm X H 2550 mm --Weight 2900 kg. --There is a crack in the plastic housing but it does not affect the functionality of the machine.

DMC UNISAND 2000 M3 Wide Belt Sander (3) Heads53" Width cap. Drum, Combination Head, Segmented PlatenHead Configuration:1st Head: Rubber covered contact roll 9" dia. 29 KW motor2nd Head: Combination Head, contact roll with graphite platen 21.4 KW motor3rd Head: Electronic Segmented Finishing platen with (46) segmented pads 18.5 KW motor.4th Station: Panel cleaning felt type head 1.74 kW, 460V, 3-phase, plus Air Cleaning headsSpecifications: -- 54" x 103" Abrasive belts with electronic tracking -- Computer controlled setup functions with keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM, 3 HP feed drive -- Vacuum conveyor bed with 10 HP motor and suction fan -- Automatic conveyor belt tensioning & trackingEquipped with & Features: -- Infeed & outfeed holddown pinch rolls on all heads. -- Motorized part thickness opening with LED readout. -- 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Infeed safety stop, outfeed emergency stop, motor load meters --High efficiency dust extraction. -- Control console with monitor.Note: Dust manifold included

DANCKAERT - 44 , ...ResawAir Strain 44"; x 5"; Bandsaw.Features & Specifications: -- McDONOUGH Center Split Feed Works. -- Wheel is supported on both sides - not cantilevered. -- Pressured guides. -- McDONOUGH Infeed Rolls. -- Max. Cut: 14";. -- New Dynamic brake. -- 60 & 100 HP. -- Control Cabinet (has battery backup and resistors to prevent spikes). -- Infeed & outfeed systems are the same. -- 24 ft. Long Camel Back chain (has air bags that are controlled by photo cell to raise & lower and index 1-board at a time). -- Max. length of lumber: 24 ft.From Seller: "The machine has a new VFDD 100 HP and a new WEG Severe Service 60 HP motor. All new hydraulic motors, caramel back chain, and roll cases."NOTE: Needs hydraulic unit.

Custom-Built DEIMCO Through Feed Sprayer with a BLASDEL IR Preheat Tunnel that is available MARCH of 2023. Until then, the System can be seen in operation. -- Line was designed to preheat Fiber Cement board prior to painting and is followed by a Single-Arm Reciprocating Sprayer with 4-Spray Gun cap. Spray Guns not included.SEE ATTACHED VIDEO FOR A GOOD LOOK AT THE LINE's OPERATION!Built in 2019, the System was used for approx. (2) years; current owner changed their process and no longer requires the equipment.Oven width cap.: 60" Wide, 1-3/4" part height cap.; overall Oven dimension: 84" Wide x 12-1/2' long x 55" high, excluding the Blower & Stack. Line/Conveyor: Variable speed drive, 18.5 FPM to 26 FPM; Reciprocator operates up to 260 FPM and set by the HMI. 2-Zone Oven: -- Zone 1: (2) Upper left side wall/ceiling mounted; 18" x 60" emitters. -- Zone 2: (2) Right upper side wall/ceiling mounted 18" x 60" emitters; 8" clearance between emitters & rolls. Heaters: Natural gas using 7" WC; 480 Volt preheat; TC, FM, flange frame. - Gas Ratings: 360,000 BTUH Max. input ; 100,000 BTUH standby input; Air Exhaust on infeed & Injection Blower on outfeed. Electrical ratings: 26.6 Amps, 480 V - 3 Phase, 60 Hz.Exhaust: 980 CFM, 1 HP Motor.Control Panel: 60 AMP Disconnect switch, ALLEN-BRADLEY "Panel View Plus HM", IEC contactor & High Temp PID exhaust.NOTE: (25) New replacement conveyor rollers & (40) reconditioned rollers for IR Tunnel.DIEMCO Sprayer complete with: (1) Reciprocating Arm holds (4) guns and reads the leading & trailing edge to turn on & off the guns as the parts feed through; best to run full width loads through Sprayer; Overspray funnels into buckets.Spray Guns turn on & off based on the part leading & trailing edge; read by a light curtain on the infeed end.Dims: GFS Spray Cabin: 13' Deep x 8-1/2' wide x 9' high surround the reciprocating arm. - Filter & Exhaust Section: 13' Wide x 3' Deep x 10' High.

DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: -- Specifications:Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. 3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: 16' long In-feed Conveyor, 10' long Transfer Conveyor, 12' long Oven Conveyor: DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: -- Specifications:Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. 3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: -- Operator & Machine Control:Built with Allen Bradley/Honeywell Components, MFM Serial: 1177, Voltage: 460V/60 Hz/25 Amp, Air: 1"; NPT 90PSIG -- Complete With:Electrically Heated Oven; 8 Cool Down Fans; 2 - Hydraulic Lift Tables; Panel Machine with Hydraulic Pump; 15’ Flash Off Conveyor; 40’ Cool Down Conveyor Includes the following for (two) flood coat machines, Conveyor System, Arbors, Paint Pump, Hydraulic Pump, Hydraulic Lift Table -- Options Complete Over-all Foot Print 175’ long x 50’ wide

DEKKER VMAX 40 HP Vacuum Pump (Liquid Ring):40 HP oil-sealed liquid ring compact motor-mounted vacuum pump system, 550 CFM, max. 29" Hg. -- Heavy duty construction:Compact design, small footprint, patented, high-efficiency DX-5 separator eliminates oil carry-over concerns; Engineered for continuous operation. -- Extended lifeSeal-fluid is not used as a lubricant. Change interval is not critical, resulting in a minimum of (10,000) Hrs. of continuous operation. Sturdy bearing pedestal mounts to standard NEMA, C-face motor. -- Direct drive and withLow speed (1,750 RPM) eliminates the use of V-belts, resulting in very low maintenance and zero downtime.Over the full vacuum range without overheating. Air cooled design and low operating noise level.

DELTA 11-990C 12" 5-Speed Bench-Top Drill PressSpecifications: -- Table size 8-1/2" x 8-1/2" with 15-1/2"; x 40"; x 11/16"; Thick Plywood top, Table tilt 40° Left/Right. -- Base size 8-1/4" x 8-1/4". -- Quill travel 2-3/8", Chuck capacity 1/2", JT33 Spindle taper. -- Spindle speeds 620, 1,100, 1,720, 2,340, & 3,100 RPM.Equipped with: -- 1/3 HP - 1,720 RPM Motor.Complete with: -- Portable Wood Cabinet.Dimensions with cabinet: 41" x 36" x 57" H

DELTA - 22-650, ...Single Planer.DELTA/INVICTA 12" Table Top (no stand) Single Planer equipped with: 2 HP motor; 3-knife round cutterhead; with rollers.Capacity of 12"; feed rate of 15-1/2 FPM.250 LBS

Delta RC-63N 24" PLANER WITH SPIRAL CUTTER HEADSpecifications -- 24" x 9" Cap., 5/16" max. material removal, -- 10-1/2" min. part length. -- 15 HP Belt drive motor, -- Spiral Cutting Head -- 5,000 RPM, variable feed speed from 20 - 60 FPM.Equipped with & Features -- Powered raise and lower of 25" x 35" table, -- Sectional chipbreakers, sectional infeed roller & dual outfeed rollers. -- Push button magnetic control, -- Dust hood, & grinding attachment to sharpen helical head knives while on the machine.

DELTA RC-51 PLANER20" x 9" Cap., 7.5 HP motor, 4-knife cutterhead, power raise-and-lower adjustment and fine adjustment thru a convenient hand wheel; variable feed speed 16 - 28 FPM; equipped with sectional chipbreakers, adjustable bed & dual outfeed rollers. Actual model 22460

DELTA RS-15 SINGLE SPINDLE SHAPERSpecifications: -- 1-1/4" interchangeable spindle. -- 7.5 HP motor with (5) spindle speeds of 2,800 - 4,500 - 6,000 - 8,000 & 10,000 RPM. -- Vertical spindle travel is 7-3/4", with 5-5/16" capacity under the nut. -- 35-1/2" x 43" fixed table with 13" max. table insert diameter.Complete with: -- Spindle reversing switch, spindle foot brake & lock, and adjustable fence. -- HOLZ Power Feeder is included