Lico Rip System with 5-Moving Blades Includes: Infeed, tilt hoist, unscrambler, Lico infeed, 125 HP gang, outfeed tunnel, 75' sort chain Lateral Scanners High speed roller gang with (5) shifting blades: Up to 500 FPM Two Scanmeg scanners Singulating infeed Saw infeed fence Hogging blade to remove inside edging Outside edging falls off and into shredder New system upgrades in 2018

Year: 2006 Working Width: 25mm to 230mm (1" to 9") Working Thickness: 8mm to 120mm (0.31" to 4.72") Bottom Spindles (x2): 40mm diameter, 0-20mm transverse movement, 6000 RPM, 5.5kW (7.5 HP) Top Spindles (x2): 40mm diameter, 0-20mm transverse movement, 6000 RPM, 7.5kW (10 HP) Side Spindles (x2): 40mm diameter, 0-20mm transverse movement, 6000 RPM, 5.5kW (7.5 HP) Configuration: Bottom, Side, Side, Top, Top, Bottom Feed Motor: 4kW (5.5 HP) Elevation Motor: 0.75kW (1 HP)

Lobo 6-Head Moulder 9" Wide capacity

GB-CIS Single-end 575V / 3 Ph / 60 Hz 5” wide rubber pad conveyor Equipped with industrial motor for full power cutting and sanding capacity

Loewer Discmaster 6TD Brush Sander Vacuum Bed

Lower Denibbing Sander

This system was purchased used and never put into service.

The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

Used Yates American Model B-26, 24” Double Planer, 75HP top, 40HPBottom, top and bottom 10 knife cutterheads, on the fly top and bottom jointers, 3 phase 480volt electrics, slide out lower cutterhead, top fixed cutterhead, 3-3/4” thickness capacity, approx. 20HP hydraulic feed works, power bed raise and lower, sectional pneumatic chip breaker, top infeed/outfeed rubber rollers.

Yates American E-12 End Matcher System for tongue and groove flooring includes: Belt, Straight Line Blade, 3-blades, Infeed conveyor to end matcher, transfer conveyor from first machine to second machine, variable speed outfeed conveyor

Planer Head Set Up Stand

220v 3 phase 2hp motor Controls work, motor runs and spindle turns Spindle raising mechanism has pin sheared in bevel gear. Includes overarm casting & mobile base.

Air Compressor Water Separator Single Phase 115V 16hz Good Condition

MAC 114LST100 Dust Collector 12x10 Rotary Airlock Hopper and leveling screws Air flow: 18,000 ACFM Media: 2,000 sq ft 12 Gauge Carbon steel exterior Clean air plenum Guard rail Nema 4 enclosureHopper discharge to match airlock Magnehelic pressure differential gauge kit (100) 6" x 144" 16 oz Polyester bags 60 HP Motor, 460 V System has already been dismantled and is ready to load.

- Min. panel length 9.06 inch - Max. panel length 10 ft 5.98 inch - Min. panel width 8.27 inch - Max. panel width 4 ft 3.18 inch - Panel stack station - no. stations 1 loading - Max. panel stack height 5 ft 2.99 inch - Work capacity 13 Cycles/min - Lifting capacity 100 Kg - Panel stack infeed - Movement system with frame System suction cups - Vacuum pump - no. pumps 1 - Control system - PLC MAGELIS

Makor Start One M (S-ONE-M) Finishing Line Infeed & Outfeed System Storage Trolleys This line has been removed from operation and is in dry storage, as shown in the last (3) photos.

System includes: Vacuum Coater UV Oven with (9) lamps Lateral Transfer Table Max width 9" Able to run clear or pigmented coating

Two Bay 52" capacity Pneumatic clamping

2005 Marathon Spray Booth 14' wide x 25.5' long x 8'9" tall Booth only no racks, spray guns, paint pots etc included

Marinus Powermax 300 End Matcher HB Precision attachment 400 v (will need transformer in US)