An electric Crown FC 5000lb forklift with very low hours only has 288 hours. Ready to move on to its next job.

1989 Cummins 500 kW Genset Twin Turbo Removed in good working order Approx 8900 hours

Curtis 7.5 HP Single Phase Compressor

4- Head customer built resaw 6" Wide belt Hydraulic hold down rollers 15 HP Motors on each head Pneumatic tension

15MM Cyclonic Air Burner -Refractory and Brick in Good Shape -Suitable for a Large Range of Drum Dryers

Daewoo G25S Forklift

671 Diesel Model PTA11112

Dewalt Radial Arm Saw

Diehl Model 75 Straight Line Rip Saw Chain is in good shape. Left and right chains are worn evenly. Includes: Laser Variable Speed: 4-speeds

The seller has upgraded to a new machine and no longer needs this rip saw. This machine still runs a few times a week at the shop. 15 HP Motor 2 HP Feed Motor 2" Arbor 16" Max blade capacity Chain drive

The seller has confirmed that this Dixie Air dust collection system is in great working/running condition and it is ready to load! - Size: 108-12 - Type: SPB - 50HP - Inlet to the motor - Circumference: 90"

This system was running daily before hte facility shut down 4-years ago. Buyer will need to provide rigging. (240) 4" x 12' Bags 100 HP Main Motor Bags are cleaned by compressed air approx every minute System is approx 1998 Approx 35000-38000 CFM

Donaldson Model ECB & ECB-2 Dust Collector - 3-units total Control Panel

DOOSAN portable lighting with only .2 hours.

Edmiston 4 Head Block Circular Sawmill Running daily Won't be available until April

Complete sawmill that is used daily. Infeed deck to debarker Morbark debarker with bark conveyor Infeed deck to mill Edmiston Sawmill: 4 HB Carriage, operator cab, drop conveyor for slabs Edmiston Edger Greenchain with rooftop Precision 48" Chipper with infeed All electrical, controls and hydraulics included

Dust blower used on Resaw or Edger 550 Volt 3 Phase 1-1/2 HP 3400 RPM

English 600 HP Boiler - (2) Units available New in 2000 One is set up for wood and only run for 3-years The second is wood/oil backup and only test fired 300' Covered Waste Conveyors available to transport waste to boilers Large capacity bucket load/silo available to store wood waste Complete loading/unloading augers available All pumps, condensate tanks, piping, electrical, catwalk, exhaust, infeed bins, suit bins, augers included. Two large stacks also available

Timber Treatment Solutions now offers an advanced incising solution for square sawn timbers with EXCALIBUR PRO, allowing a superior penetration of the wood in the subsequent preservative pressure treatment. It offers the ability to incise specific sections of post, saving on preservatives while still focusing the treatment where it is needed most and helping to retain visual product aesthetics above the ground contact line. - 1” x 1” to 20” x 20” Section Capacity - No maximum length - Incision depth up to 3/4" - 2 sets of 2 incising heads, fully sequenced with each other - Self cleaning system for blades - Incises all four faces in a single pass with incising pattern sides finishing at the same point - Full- or part-post straight-through continuous incising with a simple choice of the length and place of incision anywhere on the post - Mechanical blade separation system allows rapid setting of the machine for different timber sizes - Auto self-calibration to ensure accurate incising every time and reduce operator error

Excalibur Smart Incising for Round Timbers from Timber Treatment Solutions (TTS). - 63 mm - 200 mm Diameter (1.29"-7.8") - Minimum length of 200 mm to no max (7,8" - (9) Incising Heads - Self cleaning system for blades - Allows superior preservative penetration with pressure treatment - Optional: Customized builds for larger pole requirements