QUICK MACHINERY N-P80 Air Pod style Cold Press -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface. -- Specifications: -- Platen pressing area size: 38" x 98"; with end loading on 37" side. -- 80 PSI Platen pressure over the entire surface area with 105 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 1" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired. -- Single platen 38" X 98". -- Optional: powered roller tracksSpecifications:QUICK Laminating Pod PressN-P80-03-08-EL-1PL-M-40-R-1Z• Maximum platen pressure: 81 psi at 90 psi supply pressure• Lower platen dimensions: 3' x 8' (38" x 98")• End-loading or Side-loading: End-loading• Number of upper platens: 1• Upper platen(s) dimensions: 3' x 8' (38" x 98")• Vertical opening: Motorized adjustable from 2" to 40"• Lower platen roller tracks: Yes, Non-powered roller tracks• Number of 12.8" diameter, 5.9" stroke air pods: 24• Number of air pressure zones: 1 -- The press model shown in pictures is a dual platen powered feed through end-load press.

QUICK N-P50 Fixed Daylight Opening Air Pod PressThis Pod Press can produce a maximum 50 PSI platen pressure over the entire surface at 100 PSI supply air pressure. Press has a fixed vertical daylight opening of 44". The (18) 12.8" max. diameter air pods have 5.9" stroke.Material conveyance is via automatically extending and retracting (via pneumatic cylinders) non-powered roller tracks. A cycle timer provides visual and audible signals at the end of each cycle if desired, and also automatically releases platen air pressure at the end of each cycle, if desired.Specifications: -- Maximum platen pressure: 50 PSI at 100 PSI supply pressure. -- Lower platen dimensions: 4' x 8' -- End-loading or Side-loading: End-loading -- Number of upper platens: 1 -- Upper platen(s) dimensions: 4' x 8' -- Vertical opening: Fixed at 44" -- Lower platen Non-powered roller tracks. -- (18) 12.8" diameter, 5.9" stroke air pods. -- Number of air pressure zones: 1Lead Time: Approximately (12) weeks from time of order.Actual Model: N-P50-04-08-EL-1PL-F-44-R-1ZNOTE: Please let us know of any "Special or Specific" safety equipment requirements that you may have prior to order

QUICK MODEL L-HLPP-1-36-43-6 SINGLE SIDED HYDRAULIC LAMINATING PRESS FOR POSTS AND BEAMS: -- Number of working sections: 1 -- Maximum working length: 36'. The 36' length achieved by manufacturing the machines in two 18' long pieces; the two 18' pieces are then joined together, resulting in 36' total working length. -- Maximum working width: 43" -- Maximum working thickness: 6"Main Laminating Cylinders: -- Number of cylinders: (30) -- Size of cylinders: 80mm dia. x 80mm strokeHolddown Cylinders: -- Number of cylinders: (30) -- Size of cylinders: 40mm dia. x 150mm strokeSide Lift Cylinders: -- Number of cylinders: (2) per section = (4) -- Size of cylinders: 63mm dia.Hydraulics: -- Hydraulic pump drive motor: 7-1/2 HP -- Maximum pressure: 140kg/cm2 -- Maximum Holddown Cylinder Pressure: 50kg/cm2 -- Maximum Side Lift Cylinder Pressure: 50kg/cm2 -- NOTE: Shipped without hydraulic oil

QUICK Clamp Rack 8' -- Description: The QUICK Clamp Rack features a cleanly-designed, exceptionally strong frame, with massive 4" x 4" structural tubing cross beams and feet, and 4" x 6" structural tubing legs.The innovative “two-sided"; frame design allows for either one-sided or two-sided operation, at the shop owner’s discretion. The one-sided configuration allows for placement of the frame tightly against a wall, for maximum compactness. The two-sided configuration doubles the amount of easily-accessible clamping area, for industry-leading “room to work."; The Rack is configured by choosing either of the two available foot mounting positions. -- Specifications:96" Wide (36) Clamps 3.5" X 40" opening

QUICK R-RCGS-1-24-6 TOP GLUE SPREADER with 6" MAXIMUM OPENING. Features: -- Grooved rubber covered glue rollers are acid and heat resistant. -- Easy to clean, 5-7/8" chrome plated doctor roller. -- Comes standard with a fixed 64 FPM feed rate. -- Variable speed drive of 40 to 118 FPM is optional - ADD ...$1,090 -- Durable chain drive provides years of trouble-free operation. -- Simple to access handwheels allow the operator to make quick adjustments when panel thicknesses change. -- Complete with: Safety stop bars and roll guard hood, all-aluminum drip pan catches clean-up water.Specifications: -- 1-Sided Roller Coater (applies glue to top side of board or panel. -- Working thickness: Adjustable from 0 to 152 mm (0 to 6"); adjustable via handwheel. -- Maximum material width: 630 mm (24"). -- Application rolls quantity: 1. -- Application rolls material: SBR rubber, 60 durometer (Shore A). -- Application rolls diameter: 205 mm (8"). -- Application rolls grooving: (20) Grooves per inch. -- Doctor rolls quantity: 1. -- Doctor rolls material: Chrome-plated steel. -- Doctor rolls diameter: 148 mm (5.8"). -- Doctor rolls grooving: None (smooth rolls). -- Drive motor power: 1.5 kW (2 HP). -- Feed rate: Fixed at 64 FPM (optional: adjustable speed from 40 to 118 FPM; ADD ...$1,090) -- Includes emergency stop bars at front and back of the machine. -- Includes stainless steel waste glue drip pan. -- Includes Roll Guard's / Hoods

QUICK MODEL R-RCGS-1-36-6 TOP GLUE SPREADER with 6" MAXIMUM OPENING -- Features: -- Grooved rubber covered glue rollers are acid and heat resistant. . -- Easy to clean, 5-7/8" chrome plated doctor roller. -- Comes standard with a fixed 64 FPM feed rate. -- Variable speed drive of 40 to 118 FPM is optional - ADD $900 -- Durable chain drive gives years of trouble-free operation. -- Simple to access handwheels allow the operator to make quick adjustments when panel thicknesses change. -- Complete with: Safety stop bars and roll guard hood, all aluminum drip pan catches clean-up water. -- Specifications: -- 1-Sided Roller Coater (applies glue to top side of board or panel. -- Working thickness: Adjustable from 0 to 152 mm (0 to 6"); adjustable via hand wheel. -- Maximum material width: 630 mm (24"). -- Application rolls quantity: 1. -- Application rolls material: SBR rubber, 60 durometer (Shore A). -- Application rolls diameter: 205 mm (8"). -- Application rolls grooving: (20) Grooves per inch. -- Doctor rolls quantity: 1. -- Doctor rolls material: Chrome-plated steel. -- Doctor rolls diameter: 148 mm (5.8"). -- Doctor rolls grooving: None (smooth rolls). -- Drive motor power: 1.5 kW (2 HP). -- Feed rate: Fixed at 64 FPM (optional: adjustable speed from 40 to 118 FPM; ADD $900.00) -- Includes emergency stop bars at front and back of machine. -- Includes stainless steel waste glue drip pan.

Perforated plate type glue applicator with 8" wide x 36" long applicating grid. --When the foot treadle is released the grid is submersed into a reservoir of glue and when depressed raises the grid and part up for the excess glue to drain back into the reservoir. -- Stock to be glued is placed on the grid wich leaves a mesh pattern of glue on the bottom edge of the stock. -- Standard features include Stainless Steel applicating grid, an easy slide out Stainless Steel glue pan and glue pan cover.

QUICK F-TTGQA-12 Glue Spreader Table top unit for glue applications on a smaller scale.Equipped with: -- 1/4 HP Motorized 60 RPM steel roller and an approximately (2) quart capacity stainless steel reservoir; both easily removable for clean up. -- Spread roller, rubber grooved - roller dimension 12" X 6"; speed of roller 92 FPM. -- Table top dimension: approximately 2' X 3'. Options: To keep the glue fresh and from cleaning the reservoir daily (1) F-TTGA-COVER-12 Stainless Steel Cover for TTGA, 12" wide, please add ...$195.00.

QUICK R-RCGS-1-24 Top Roll Glue SpreaderGrooved rubber covered applicator roller is acid and heat resistant. -- Easy to clean, 5-7/8" chrome plated doctor roller. -- Comes standard with a fixed 80 FPM feed rate. -- Durable chain drive gives years of trouble-free operation. -- Simple to access handwheels allow the operator to make quick adjustments when panel thicknesses change. -- Complete with: Safety stop bars and roll guard hood, stainless steel drip pan catches clean-up water. -- Variable speed drive of 40 to 118 FPM is optional

Grooved rubber covered glue rollers are SBR / acid and heat resistant. -- Easy to clean, 6-7/8" hardened rubber doctor roller. -- Comes standard with a fixed 80 FPM feed rate. -- Durable chain drive gives years of trouble-free operation. -- Simple to access handwheels allow the operator to make quick adjustments when panel thicknesses changes up to a 1-3/4" opening. -- Complete with: Safety stop bars and roll guard hood, all aluminum drip pan catches clean-up water. -- Also Avalable with: -- 17" Wide -- 24" Wide -- 36" Wide. -- 48" Wide. -- Variable speed drive of 40 to 118 FPM. -- 6" or more Opening.

SCMI SIGMA PRIMA 50 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications: Working cap:149.6" (3,800 mm) Max. rip cut cap. 125.9" (3,200 mm) pusher stroke; 1.96" (50 mm) max. saw blade projection; 12 HP (9 kW) main saw motor (3,900 RPM); 2 HP (1.5 kW) scoring saw motor (6,300 RPM).Main blade diameter: 11.8" (300 mm), Main blade arbor diameter: 80 mm; Scoring blade diameter: 6.37" (160 mm), Scoring blade arbor diameter: 55 mmAutomatic exclusion of scoring unit when motor is in off position. -- Saw carriageFeed speed 0 - 327 FPM (0 - 100 MPM), return speed 327 FPM (100 MPM),Automatic saw carriage lubrication, balanced on hardened cylindrical guides; external score saw adjustment, THK guides for vertical saw movement. -- Pusher Fence:Feed Speed 0 -230 FPM (0 - 70 MPM) forward speed, 230 FPM (70 MPM) reverse speed;Programmable rear fence with (7) material gripper clamps, rack & pinion movement,Grippers fit into a slotted pressure beam for positive material control during the final cut. -- Operator & Machine Control:PC front-end with: SCM Real time "WinCut" + Windows "7 Professional" operating system; Pentium 300 MHz, 6.4 GB hard drive, 64 MB RAM,17" color super VGA flat screen monitor, on-screen diagnostics & production reports; (2) serial ports & (1) parallel port, spacing available for networking cards. "Cutty" optimization software is included which allows: 30 lines per program, 300 max number of pieces per line, and 3 cutting levels. -- Complete with:Side alignment device: Min. part width 2.36"; Max. part width 48"; Rear support rails with rollers;(1) Front fixed air table 98" x 24" (2,500 x 609 mm), (2) Adjustable air tables 59" x 24" (1,500 x 609 mm).Plastic safety guards; emergency stop bar; enclosed cutting area; triple dust collector outlet. -- Actual model is SCMI SIGMA PRIMA 50.

SCMI K 203 SINGE SIDED EDGEBANDER5/16" (7.9 mm) Max. edge cap. for strip feeding, 1/8" (3 mm) for coil feeding; 60 mm min. panel width and 160 mm min. panel length; panel thickness 10 - 50 mm.Equipped with: -- Teflon coated glue pot (heat-up time 10 Min), automatic strip and coil feed magazine, 3 mm cap. guillotine, 3-roll pressure unit w/pneumatic control.Workstations: -- Double motor front & rear end trim mounted on THK guideways (0.4 HP - 12,000 RPM motor ea.), tilts 0° - 15° from the control panel with (2) preset positions. -- Top & bottom flush & bevel trims with quick release mount and plug-in motors for quick tooling changes (0.7 HP - 12.000 RPM motor ea.), bevels 0° - 15³ with precision digital indicators for quick setup. -- Top & bottom Scraping station -- Top & bottom buffing unit (0.25 HP - 2,800 RPM motors). -- 36 FPM Fixed feed speed, 0.75 HP feed drive.Complete with: -- Microprocessor for line control (can store up to 50 preset programs), control panel at eye level for easy programming, full cover sound enclosure. Features: -- Mechanical digital readouts for setup adjustments, frequency inverter and outboard panel support.

SCM Sandy 900-RRCS-135 Wide Belt Sander (3 ) HeadsWidth cap 53", Drum, Drum , PlatenHead Configuration:1st Head :Planer Head2nd Head: Grooved Rubber contact Drum 15 HP3rd Head: Superfinishing Unit: Provides uniform finish using a Chevron belt and an electronic pad, 15 HPSpecifications -- Working Width: 1,350 mm -- Min/Max Thickness to Be Machined (with Mobile Table) 4 - 170 mm; Min/Max Thickness to Be Machined (with Fixed Table): 4 - 200 mm -- Sanding Belt Width/Length: 1,370 & 2,620 mmEquipped with & Features: -- Chevron belt and an electronic pad, eye-S Control: allows easy and intuitive programming with an LCD display and touch-screen function. -- Unskilled Operator Friendly: Stores up to 120 work programs for commonly used machine settings.

SCM TECH Z 30 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications:Working Field "X" axis 120" (3,050 mm); "Y" axis 52.7" (1,340 mm) for routing & 44" (1,118 mm) for boring; "Z" axis stroke 7.8" (200 mm); max. material thickness 3.9" (100 mm). -- Positioning Speed:"X" & "Y" Axes are 197 FPM (60 MPM); "Z" axis is 72 FPM (22 MPM).Axes positioning by: AC Brushless motors and YASKAWA drives; high precision ball screw drive system in "X", "Y". "Z" Axes;All axes ride on prismatic guideways & sliding blocks. -- Worktable:(6) "TV" Tubeless mobile support rails, (2) vacuum pods per rail; (4) pneumatic lifter rails for heavy panels.(6) Pneumatic pop-up backstops, (6) pneumatic pop-up front stops; (2) pneumatic pop-up side stops.LED Display positioning assistance for the support rails & vacuum pods; (2) independent working fields. -- Boring Head:3 HP (2.2 kW) motor - 4,000 RPM; (15) independent vertical spindles: (8) Spindles in "X" & (7) spindles in "Y".(6) Horizontal spindles (2 + 2) in "X" & (1 + 1) in "Y-axis".(1) X-axis grooving saw with 100 mm dia. blade - 6,000 RPM. -- Machining:(1) 10 HP (7.5 kW) Electro-spindle router with: HSK F63 Adaptor; variable speed from 1,000 - 24,000 RPM, max. torque achieved at 12,000 RPM.Static inverter for stepless speed & rapid shutdown rotation.(1) 6-Position ATC tool plate mounted on the on the machine for "on the fly" ATC; max. tool weight is 8 kG (17.6 Lbs). -- Operator & Machine Control:PC Front-End with: SCM "UNIVERSAL K2" + "Xilog Plus" + Windows "XP" Pro Operating System; 15" CRT color display, CELERON 2 GHz processor, enclosed in air-conditioned cabinet. -- Complete with:(1) 100 m³/Hr Vacuum Pump; automatic lubrication system; "BUMP STOP" safety system. -- Actual Model is SCM TECH Z30 R6

SCM SANDYA - 40 M3 135, ...3-Head Wide Belt Sander 52" Width cap. Drum, Drum, Combination HeadHead Configuration:1st Head: Steel Contact 22 kW Pneumatic blowdown and alignment.2nd Head : Rubber Contact 18.5 kW Pneumatic blowdown and alignment.3rd Head: Combination Platen 15 kW Pneumatic blowdown and alignment.Note:The SCM sander does not have a brush. After the 3rd head, it has this pneumatic blow-off bar with multiple blow-offs running the length of the sanders width. Sander can be seen under power if needed.Specifications: -- 53" x 103" Abrasive belts with electronic tracking. -- All heads with abrasive belt grit compensation. -- Conveyor belt feed with dual feed speed, 5 HP motor. -- Automatic part thickness adjustment. -- Motorized thickness opening via (4) precision conveyor bed jacks with LED readout. --0" - 7-7/8" opening. -- Equipped with & Features -- Outfeed rubber covered holddown rolls or shoes on all heads. -- Motor load meters. --Infeed and outfeed conveyor extensions. -- WYE-DELTA soft start.Note: The SANDYA model "40" is more or less the same as the SANDYA "30" but more Heavy Duty.

SCM SANDYA 15S (3) Head Wide Belt Sander42" Width cap, Drum, Drum, Combination HeadHead Configuration:1st Head: Steel contact roll, 7" dia., 35 HP motor;2nd Head: Rubber-covered contact roll, 24 HP motor3rd head: Combination head, rubber-covered contact roll (45 Shore) and 3" wide finishing platen, 17.4 HP motor.Specifications: -- 43" x 103" Abrasive belts -- Electronic tracking & pneumatic belt tensioning, abrasive belt grit compensation. -- Conveyor belt feed with dual feed speed, 4 HP motor -- Automatic part thickness adjustment -- Motorized thickness opening via (4) precision conveyor bed jacksEquipped With & Features: -- LED readout, 0" - 6-1/4" opening. -- Infeed & outfeed spring loaded rubber covered hold-down rollers -- Motor load meters -- Infeed and outfeed roller conveyor extensions.

SCM Sandy 10 -RCS-110 Wide Belt Sander (2) Heads43" Width cap. Drum, Combination HeadHead Configuration:1st. Head: 7" diameter corrugated metal roller for calibration 35 HP ( Drives both Heads )2nd Head: Combination head with 7" dia. contact roller (spiral grooved rubber covered); air/jump finishing platen controlled with timers to eliminate any rounding on leading & trailing edges of the panel, 2" wide platen.Specifications --103" long x 43" wide Abrasive belts --Air tracking, floating & rigid bed for sanding of veneers & solid panels; infeed & outfeed spring loaded holddown rolls -- Minimum workpiece length 16" --Thickness capacity 6.25". --Separate 2.5 H.P. variable speed feed motor delivering feed speeds from 15 to 70 FPMNote: The seller has 20 boxes of various sandpaper belts (80 – 150 grit) that will be included.

SCM M3 Multi-Blade Dip Chain Gang Rip SawSpecifications: -- 300 mm (11.81") Width cap. -- 110 mm (4.33") Max. depth of cut. -- 8-3/4" Throat depth. -- 390 mm (15.35") Min. stock length. -- 200 - 350 mm (7.87" - 13.78") Blade diameter. -- Arbor dia. 70 mm (2.76"). -- Table size 750 x 1,530 x 750 mm H (29-1/2" x 60.24" x 29-1/2" H). -- Blade speed 4,200 RPM. -- Feed speeds 6 - 48 MPM (19 - 157 FPM).Equipped with: -- 44 kW (60 HP) - 3,554 RPM Blade motor. -- Variable speed drive feed chain motor. (2) Upper infeed & (2) Upper outfeed 4" Dia. rollers, Automatic chain lubrication. -- Top & bottom anti-kickback fingers. -- Main dust hood, with 200 mm (7.87") Dia. outlet. -- 40"; x 2-3/4"; H Adjustable infeed fence. -- Motor load meter.Complete with: -- Operation & Maintenance Manual. -- Tooling (As pictured).

SCM OLIMPIC K230-EVO SINGLE SIDED EDGEBANDERSpecifications: --0.4mm to 3mm Edge thickness, Panel thickness 8mm to 50mm (3/8" to 1-15/15"), minimum part width 110mm (4.33"), minimum part length 160mm (6.30"). -- Equipped with: -- 1.5 Kg Teflon-coated glue pot, glue roller application system complete w/automatic recycling device for unused glue, digital thermostat adjustment for temperature control. pneumatic guillotine, 3-Roll pressure unit w/pneumatic controls for all pressure rollers. -- Automatic strip & coil feed magazine --Workstations: --÷Double motor front & rear (0.4 HP - 12,000 RPM motor ea.), tilts 0° - 15°, end trimmers mounted on 45° THK guide. --Top & bottom flush & bevel trims with quick release mount and plug-in motors for quick tooling changes (0.7 HP - 12.000 RPM motor ea.), bevels 0° - 15° with precision digital indicators for quick setup. --Top & bottom scraping unit w/pneumatic positioning from the control panel. -- Top & bottom buffing unit (0.25 HP - 2,800 RPM motors). 29.5FPM Fixed feed speed, 0.75 HP feed drive.

SCM STARTECH CN - CNC MULTI SPINDLE DRILLINGFeatures: -- Easy Motion Work Table -- 7" Touchscreen -- (7) Independent Vertical Boring SpindlesSpecifications: -- Maximum Panel Dimensions X-Y-Z (3050mm x 800mm x 50mm), Minimum Panel Dimensions X-Y-Z (300 mm X 90 mm x 10 mm) -- Drilling/Grooving working area: 0mm x 800 mm/0mm x 800 mm ÷X-Axis Stroke: 750 mm÷X-Y maximum axis speed: 25m/Min. -- Vertical Spindles: 7 (4X-4Y one of them is shared) Horizontal Spindles: (along Y-axis): 2 (1+1) -- Horizontal Spindles: (along X axis): -- 1 Fixed Integrated Blade (cutting into direction): X Blade Diameter: 100 mm Maximum Blade Thickness: 5 mm -- Motor Power: 3 HP (2.2 kW) Spindle Rotation Speed: 3350 RPM÷Blade Rotation Speed: 4300 RPM -- Electrical Supply: 230 Volt (60 Hz) Installed Motor Power: 4.5 KVAHigh-performance numeric controlled (NC) Drilling Machine engineered for full-production woodworking shops and craftsmen. The Startech CN drilling head's seven (7) independent vertical spindles, the spindle and blade in the “X"; axis, and the possibility of drilling in the “Y"; axis make it both flexible and ideal for batch furniture productions. This machine allows the operator unparalleled flexibility for tailored products without the need of operator intervention for the worktable and machine set-up according to the panel dimensions.