GANNOMAT COMBI 110 CONSTRUCTION LINE BORER(23) Spindle head, 2 HP - 2,800 motor, 31-1/2" max. working width, 3" drilling stroke, drills vertically from bottom and horizontally from rear, tilts pneumatically from lower to rear position with positive stop at 45° for angle drilling. -- Holddown clamp assembly tilts 90° for clamping short panels vertically for edge boring, no need to swivel boring head, hydraulic brake for through boring. -- Complete with: (4) Pneumatic holddowns, mirror imaging fences, 4,000 mm line boring fence w/stops and 1,500 mm butt joint fence with (2) flip stops.

GANNOMAT INDEX 280 TREND CNC BORE, GLUE & DOWEL INSERTER: -- Specifications:CNC Controlled horizontal Point-to-Point Drilling, Gluing & Dowel Inserting Work Center for absolute, incremental, variable (parametric) programming of boring patterns. -- Working Field(4) Independent zones for individual processing of (1 - 4) pieces. Pneumatically activated Stop system (side fences) consisting of: Right-hand, left-hand, and center stop. Max. single part Length 2,800 mm (110"). As a 2-zone: LH & RH is 1,400 mm (55") each part. As a 4-zone with center fence: LH/RH is 700 mm (27.5") each part.Min/Max. Material Thickness 0.50" - 3.125" "X" Axis Positioning Speed 246 FPM (75 MPM) and driven by rack & pinion for fast acceleration/deceleration of working unit. "Y" Axis is set by mechanical digital counters. "Z" Axis is NC controlled height adjustment for boring/inserting units. -- Hold-down Clamps:Total of (10) pneumatic, "quick change" Hold-down Clamps. -- Dowel driving & horizontal boring:Integrated into (1) station; the Dowel Driving Unit is located alongside the Boring Station; both units are mounted on (1) support. -- Horizontal Drilling Spindle:Can be setup for 6 - 8 or 10 mm; dowel length from 25 - 50 mm. -- Doweling Station includes:Vibrating hopper with: (1) Single drop device and (1) outlet tube; insertion head & dowel driving with air impulse.Mechanical dowel diameter & dowel length control prevents the insertion of any oversized dowels. -- Glue Valve/Amount:Controlled via software and can be adjusted by milliseconds; (2) standard separate stainless steel 1.5 gal. pressurized tanks (one for glue, one for water to clean/purge the glue tubes. -- Operator Interface:GANNOMAT + BECKHOFF "C3640 Twincat" PLC Operating System.15" Touch-Screen color monitor; network card (for online operation); serial, parallel, USB ports. -- Actual model is: GANNOMAT INDEX 280 TREND. NOTE: Machine is currently setup for 8 mm dia. x 35 mm long dowels.

GANNOMAT - 260: Case Clamp (Semi-Automatic) Specifications 100" x 50" x 26" Clamping Cap. -- (3) Vertical combination air cylinders & shoes; mounted on horizontal beam for top pressure; 0.33 HP motor for up/down travel. -- (2) Combination air cylinders & shoes mounted on adjustable vertical, side pressure beam. Vertical beam locks in place with: (4) Air cylinders and rides on bearings for quick and easy positioning. -- Push button operated w/independent pressure control for top or side; air pressure up to 125 PSI (Clamp shoe assemblies are interchangeable from vertical to horizontal). -- Complete with:Pressure gauges; timer control with: (0 - 30) Min setting.

Gannomat INDEX 470 TB CNC BORE GLUE & DOWEL INSERTER:Specifications: -- The GANNOMAT "Index 470 TB" is a CNC Controlled Point-To-Point Drilling/Gluing/Dowel Insertion Machine for variable programming of boring patterns -- "X" Axis CNC Controlled via precision ball screw Servo drive; "Y" & "Z" Axis adjusted via mechanical spindles; set by manual digital indicatorsWorking width: -- 1,300 mm (51") x 3/4" to 7-3/4" width x 1/2" - 3-1/8" material thickness with (2) fields; LH/RH (mirror image). -- (8) Vertical hold-down cylinders for horizontal part processing. -- Dowel driving & horizontal boring integrated into (1) station; the dowel driving unit is located alongside the boring station; both units are mounted on (1) support. -- Horizontal drilling & boring station head setup for 6 - 8 or 10 mm; dowel length from 25 - 50 mm.Dowel Station includes: -- Vibrating hopper; insertion head & dowel driving with air impulse; setup for 8 mm dia. x 50 mm long dowels. -- Glue valves controlled individually at Control Cabinet; central adjustment for the amount of glue by means of digital timer.Operating System: -- MS-XP & GANNOMAT production software; 15" color touchscreen monitor interface, USB drive, bar code capable, Controller & Drive:BECKHOFF "C3620 TWINCAT V2.10"Complete with: -- (1) glue tank, (1) water tank, auto-lubrication system

GANNOMAT INDEX 130 LOGIC CNC BORE, GLUE & DOWEL INSERTER (W/Top Drilling Option): -- Specifications:The GANNOMAT "INDEX LOGIC" is a CNC Controlled Point-to-Point Drilling/Gluing/Dowel Insertion Machine for variable programming of boring patterns. -- "X" & "Y" Axis set by manual digital indicators; "Z" Axis adjusted via CNC controlled Servo drive. -- Working width:1,300 mm (51") x 3/4" - 7-3/4" Width x 1/2" - 3-1/8" material thickness with (2) field, LH/RH (mirror-image). - Table size: 4-1/2" x 52-3/4" x 35" H with 9" x 52" extension. -- (6) Vertical hold-down cylinders for horizontal part processing. -- Dowel Driving & Horizontal Boring: Integrated into (1) station; the dowel driving unit is located alongside the boring station; both units are mounted on (1) support. -- Horizontal Drilling & Boring Station: Head can be setup for 6 - 8 or 10 mm, dowel length from 25 - 50 mm (currently set up for 8 mm dia. x 50 mm long dowels). -- Doweling Station: Vibrating hopper; insertion head & dowel driving with air impulse; glue valves are controlled individually at the control cabinet; central adjustment for the amount of glue by means of a digital timer. -- Operator Interface: MS-XP & GANNOMAT Production software; 15" color touchscreen monitor interface; USB drive; bar code capable. -- Controller & Drive: BECKHOFF "C3620 TWINCAT V2.10". -- Complete with: (1) Glue tank; (1) water tank; auto lubrication system, and all original manufacturer's machine documentation. -- Included Options: An optional Single Spindle top drilling spindle with a Z-axis control. Barcode Scanner easily retrieves prewritten stored programs in an instant. -- Actual Model is: GANNOMAT INDEX 130 LOGIC.

GANNOMAT DB21 CONSTRUCTION/LINE BORINGSpecifications: --Vertical/horizontal drilling, (21) spindles. -- Drills vertically from the bottom-up, horizontally from the back. -- 21-Spindle head, 2 HP motor - 3,000 RPM spindles on 32 mm centers. Complete with: -- (3) Overhead hold-down clamps, frontal top stops, 70" (1,800 mm) Left & right side fence,line boring fence.

GANNOMAT CONCEPT 70/170 EASY, ...CASE CLAMP (SEMI-AUTOMATIC):Specifications:This solid platen Case Clamp is specially designed to save space, time and labor in all production situations. Whether it is your only Clamp or a second Clamp, the "Easy 70" gives you faster cabinet assembly production.Features: -- Minimal floor space required: Length (79"), Width (32"), Height 82.6". -- Pressing force is exerted along the horizontal axis of the dowel joint by the side pressure beam. -- Continuous working surfaces (fixed sidewall and side pressure beam) eliminates setup time for carcasses with fixed shelves, stretcher rails, etc., and small carcasses like drawer boxes.Working Capacity: -- Min. clamping width 6";, max. clamping width 51.2";, max. clamping height 66.9". Equipped with: -- Adjustable Clamping cycle time w/auto. opening. -- Simple operation by directional push buttons. -- Potentiometer for stepless adjustable pressing force. -- (3) Pressing velocities and adjustment rates: 5, 10, and 25 MPS (with fine positioning or creep feed). Actual Model is GANNOMAT -CONCEPT 70/170 EASY

Sutorbilt Legend 5M -- Standard, medium-pressure -- Diameter (inlet/outlet): 4" NPT -- Shaft size: 1.125" -- 2,350 Max RPM

2L Sutorbilt -- 5 HP Motor -- 5,275 Max RPM -- Pressure to 15 PSIG -- Flows to 3015 CFM

GENERAL - 350 10", ...Tilting Arbor Table Saw with: 5 HP Motor & Rip FenceSpecifications: -- Table size: 20" LR x 28" FB x 34-1/2" H. -- Arbor dia. 5/8"; tilt 0° - 45° to right; blade speed: 4,000 RPM. -- Max. depth of cut: 3-1/8" at 90°; 2-1/8" at 45°; max. width of dado cut 13/16". -- Max. rip cap.: 52" Right.Equipped with: -- 8" Left & right table extensions. -- 5 HP Motor.Complete with: -- DELTA "Unifence Saw Guide"; 43" L x 3-1/2" H Rip Fence System. -- Blade Guard. -- Miter Gage.

GENOX V600 New Single Shaft ShredderIn Stock - Ready to Ship!Features --Shock Absorbing Gearbox that reduces stress on Drive Components -- 25HP -- Hopper Opening - 48" x 43" -- Rotor Diameter - 9" --Rotor Knives that can be used on four edges before replacement. --Durable Counter Knives that adjust to maintain cutter clearance --Quick Change Screens for accurate particle size control --Segmented Shredding Chamber Floor with Brass Guides --Twin Speed Hydraulics with an integrated air cooler --Stand Alone Electrical Control Panel with Siemens PLC Control System --Tested, Approved and Certified to the applicable CE safety standardsTypical Applications --Plastics --Wood --Cable --Paper --Aluminum --Foam --Textile

GENOX V800 New Single Shaft ShredderIn Stock - Ready to Ship!Features: -- Shock Absorbing Gearbox that reduces stress on Drive Components -- 50 HP motor -- Hopper Opening - 59" x 56" -- Rotor Diameter - 15.75" -- Rotor Knives that can be used on four edges before replacement. -- Durable Counter Knives that adjust to maintain cutter clearance -- Quick Change Screens for accurate particle size control -- Segmented Shredding Chamber Floor with Brass Guides -- Twin Speed Hydraulics with an integrated air cooler -- Stand Alone Electrical Control Panel with Siemens PLC Control System -- Tested, Approved and Certified to the applicable CE safety standardsTypical Applications --Plastics --Wood --Cable --Paper --Aluminum --Foam --Textile

GIARDINA DUALTECH 605 Automatic Reciprocating Sprayer:GIARDINA, model DUALTECH 605. Automatic reciprocating Spray Machine.System includes: -- In-feed roller conveyor with panel reading/detection 60-cell photodiode bar to monitor and regulate spray application, further maximizing application transfer efficiency. -- (2) Reciprocating trolleys with spray gun supports, and adjustable speed, providing a consistent speed and pattern across entire conveyor width. - Each trolley to carry (4) adjustable guns on each head (8 guns total). -- Two (2) coating circuits, suitable for solvent and water-based coatings. -- Motorized height adjustments of spray gun supports. -- Spray guns are independently adjustable in inclination; and manual adjustment. -- Through Feed Conveyor: Max. working width of 1,300 mm (51"), variable speed adjustable by means of an inverter. -- Synthetic Belt Conveyor: Ring-closed by means of an "overlapped" joint and with solvent-resistant surface treatment.Features: -- Total recovery of the lacquer deposited on the belt and cleaning of the belt with the possibility of reusing it in the spraying circuit. - Rapid repositioning of the conveyor belt system thanks to the special design of the frame. -- Air exhaust system and separation of the solid content from the air by means of two (2) suction boxes located on the two sides of the conveyor, equipped with high-efficiency twin Dry-Filters. The filtered air is exhausted to the outside by means of a centrifugal fan. -- The Enclosure Booth is made with structural irons and coated sheet steel panels. -- Control and set-up of the work parameters by means of a PLC located on a pivoting arm mounted to the machine.NOTE: Is being "Cleaned, checked and Serviced" by on of the most experienced Finishing Equipment Technician!

GIBEN KG-468-JKS EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Working Capacity: 0.4 - 3 mm Edge thickness capacity; minimum panel width 80 mm; minimal panel length 120 mm; panel thickness 10 - 60 mm adjustable feed speeds 10/15/20 MPM; motorized adjustment of the upper pressure beam. -- Equipped with: PREMELTING Glue System with: Quick change glue pot; top pot capacity 5 kG (11 Lbs); lower pot capacity 2 kG. -- Adjustable pressure roll section with: (1) Driven roller and (3) idler rollers.Workstations: -- 2-Motor Pre-milling Unit with independent adjustments. -- 2-Motor End Trimming Unit. -- Top & Bottom rough trim station. -- Top & Bottom radius fine trim station. -- 2-Motor Corner Rounding Unit. -- Top & Bottom profile scraping station. -- Top & Bottom flat scraping station. -- Top & Bottom Buffing station.Complete with & Features: -- "DELTA" PLC Control. -- Sound cabin for all workstations. -- Adjustable 700 mm outboard panel support. -- Actual Model is: GIBEN KG-468-JKS

GIBEN - G4 512, ...CNC Router with ATC and Boring: 5' x 12' "Matrix" grid Phenolic surface for "Nested Base Manufacturing". -- Working capacity:X-Axis 145.6" (3,700 mm), Y-axis 62.9" (1,600 mm), Z-axis stroke is 9.8" (250 mm), max. material thickness 4.7" (119 mm). -- Positioning Speed:X- & Y-Axis 262 FPM (80 MPM), Z-axis 98 FPM (30 MPM).X- & Y Axes use a precision Rack & Pinion system, Z-axis uses precision ball screws.All axes movement is on precision linear guides & ways and controlled by digital, brushless AC Servo motors.All motion components are maintained by an automatic lubrication system. -- Work area:Flat table design with "Matrix" grid phenolic surface for "Nested Base Manufacturing".(2) Side clamps + (4) external pneumatic pop-up stops for piece positioning at (4) corners of workstations; Automatic NC controlled 8-zone vacuum table.Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward shaped parts; with "quick connect" vacuum outlet for custom vacuum pods & fixtures. -- Boring Unit:(1) 2.5 HP (1.7 kW) motor, speed 6,000 RPM, "HSD" Boring unit.(9) Independent vertical spindles with: (5) in X-axis & (5) in Y-axis. -- Machining:(1) 15 HP/18 HP peak Air-cooled "ANDERSON" Electro-spindle with: HSK F63 Adaptor, RH & LH rotation; variable speed from 1,000 - 22,000 RPM.(1) 8-Position ride-along ATC tool changer for "on the fly" ATC. NC Controlled "touch-off probe" tool presetting for the measurement of the tool length. -- Operator & Machine Control:PC Front End with ANDI/GIBEN "SYNTEC 21MA PC based Controller" + "WINDOWS" Operating System.19" LCD Flat screen monitor; Server, full keyboard, and mouse all mounted on a mobile cart.Intel(R) Core i CPU; 8 GB RAM memory; 500 GB (SSHD) hard disk; Dedicated graphic card; DVD reader; USB ports; Ethernet card for network connection capabilities. -- Complete with:(2) 250 cbm/Hr (9 HP) "BECKER" vacuum pumps, tool holders, Collets, tool changing stand and manuals. Automatic program update according to the tool length (touch-off probe).Automatic Lubrication system for linear guides, pads, and recirculating ball screw. Teleservice capabilities; perimeter Safety light bars & perimeter fencing; Manuals & Documents on CD. -- Actual Model is GIBEN - G4 512. Machine footprint Floor area 472"; x 197";

GIBEN KS26J Edgebander with Pre-Milling & Corner RoundingSpecifications: -- Edge thickness 0.4 - 3 mm. -- Minimum panel width 80 mm, Panel thickness 8 - 50 mm. -- Feed speed 16 MPM, Mechanical adjustment of the upper pressure beam.Equipped with: -- 2 Liter Glue Teflon coated tank with Quick heating system. -- Adjustable pressure roll section with (1) Driven roller & (3) Idler rollers.Workstations: -- 2-Motor Pre-milling unit with Diamond tooling and with Independent adjustments. -- 2-Motor End trimming unit. -- Top & bottom trim station with diamond radius tooling . -- Double motor Corner Rounding unit. -- Top & bottom radius scraping station. -- Top and bottom Buffing unit.Complete with: -- PC Touch screen control. -- Sound cabin for all workstations. -- Adjustable outboard panel support.

GIBEN G4 EVO 510 CNC ROUTER (ATC & BORING) + RAKE & OFF LOADING: -- Specifications: 5' x 10' "Matrix" grid Phenolic surface for "Nested Base Manufacturing". -- Working capacity:X-Axis 126" (3,200 mm), Y-axis 62.9" (1,600 mm), Z-axis stroke is 9.8" (250 mm), max. material thickness 4.7" (119 mm). -- Positioning Speed:X- & Y-Axis 262 FPM (80 MPM), Z-axis 98 FPM (30 MPM).X- & Y-Axes use a precision Rack & Pinion system, Z-axis uses precision ball screws.All axes movement is on precision linear guides & ways and controlled by digital, brushless AC Servo motors.All motion components are maintained by an automatic lubrication system. -- Work area:Flat table design with "Matrix" grid phenolic surface for "Nested Base Manufacturing".(2) Side clamps + (4) external pneumatic pop-up stops for piece positioning at (4) corners of workstations; Automatic NC controlled 8-zone vacuum table.Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward-shaped parts; with "quick connect" vacuum outlet for custom vacuum pods & fixtures. -- Boring Unit:(1) 2.5 HP (1.7 kW) motor, variable speed up to 6,000 RPM, "HSD" Boring unit.(9) Independent vertical spindles with: (5) in X-axis & (5) in Y-axis. -- Machining:(1) 15 HP Air-cooled "ANDERSON" Electrospindle with: HSK F63 Adaptor, RH & LH rotation; variable speed from 1,000 - 24,000 RPM.(1) 8-Position ride-along ATC tool changer for "on the fly" ATC. NC Controlled "touch-off probe" tool presetting for the measurement of the tool length. -- Operator & Machine Control:PC Front End with ANDI/GIBEN "SYNTEC" + "WINDOWS" Operating System.19" LCD Flat screen monitor; Server, full keyboard, and mouse all mounted on a mobile cart.Intel(R) Core i CPU; 8 GB RAM memory; 500 GB (SSHD) hard disk; Dedicated graphic card; DVD reader; USB ports; Ethernet card for network connection capabilities. Automatic program update according to the tool length (touch-off probe).Equipped with: Automatic Lubrication system for linear guides, pads, and recirculating ball screw. Teleservice capabilities; perimeter Safety light bars & perimeter fencing; Manuals & Documents on CD. -- Actual Model is GIBEN - G4 EVO 510.Note: No vacuum pump includedTear down and loading not included

GIBEN G2 GENESIS 48 CNC ROUTER (ATC & BORING):4' x 8' Fixed table, moving gantry machine with a single-zone vacuum table. -- Equipped with:(1) 12 HP ISO-30 Type ATC spindle, air-cooled, ceramic bearings, variable spindle speed from 6,000 - 24,000 RPM. -- 6-Station automatic tool changer and 2 HP 9-spindle vertical drill bank (5 in X- & Y-axis). -- Axis stroke:1,300 mm 51" in Y-Axis, 2,500 mm 98.4" in X-Axis, and 200 mm in Z-axis. -- Max. feed rate:60 MPM (2,362 IPM) in X- & Y-axis, 30 MPM (1,180 IPM) in Z-axis. -- Equipped with & Features:Tool Length Measuring System (Tool Touch Off device). -- Control:ANDI/SYNTECH Controller with network compatible WINDOWS PC based front end, color monitor, keyboard, and mouse.Full function handheld pendant, absolute & incremental programming, cutter & tool length compensation, feed rate & spindle speed override, inch/metric operation, and linear/circular & helical interpolation. -- Complete with:10 HP BECKER Vacuum Pump. Tool Holder’s collets and Light safety fences. -- Maintenance supplies (grease, grease guns), and full manuals, and product literature.

Gomad "DFDA-455" Sliding Table Single Spindle Shaper -- Specifications: 2 -1/64" (55 mm) spindle currently, 7.5 HP belt drive motor, (4) speeds 4,000/6,000/8,000 & 10,000 RPM, 3-9/16" spindle travel, 3/4" up to 2-11/64" dia. interchangeable spindle, reversing spindle rotation; heavy duty 36" x 40" cast iron table, (3) pneumatic clamps, double end fence, 4.5" dia. dust chute. -- Complete with: 13" wide sliding table, (4) Hold down springs, mounting collars & bolts, miter gauge with stop rod, and foot brake, capable of doing arch moulding work.NOTE: Great running condition before disconnect in 2013, currently stored in facility basement.

GOODSPEED FH30 Semi-Automatic Copy Lathe. Specifications: --30" Cap. with a 3" max. dia., hopper feed for square or round stock, 15 HP main spindle motor for 2,250 - 3,200 - 3,825 & 4,625 RPM; reciprocating tail spindle. -- 2 HP Hydraulic feed on back knife; up to (900) pieces/Hr capacity. -- Complete with: Carriage slow down control system, pressure lubrication die system, 2-belt head spindle drive, and adjustable knife bar for cutting tapers. -- Includes: Pneumatic steady rest; Custom pressure reducer; used tooling and extras. -- Original manual included. -- Was used for making drumsticks.