COSTA K6 WCCT 1350 4-Head Planer / Sander 4-Head with Planer, Drum, Drum and Combination headSpecifications: -- Front head #1 54" Helical planer head with (480) insert knives 34 kW or 45 HP motor. this is a removable head complete with cart for cleaning and changing knives. -- Head #2 Drum currently set up with 100 grit abrasive sanding belt 22 kW or 30 HP motor., -- Head # 3 Drum with 150 grit abrasive sanding belt 17 kW or 22 HP motor. -- Head # 4 Combi head with timed air bladder platen, currently runs 180 grit abrasive sanding belt, 14 kW or 20 HP motor. -- Feed mat speed from 4 - 20 feet per minute. Features: -- Capable of planning off 1/8" and sanding to 180 grit in one pass. -- Uses 52 - 54" x 103 abrasive sanding belts. -- Vacuum feed mat only surfaced 2 or 3 times, PLENTY of life left in it. -- Used in small shop running no more than 5 -10 hours a week, on a machine designed to run 3 shifts. -- Features Air scrubber unit on the out feed to remove any additional dust. Note: Machine was purchased New in February 2016

--This machine is in Auction @ https://exfactoryauctions.com/Detail/FD-230117/event/A122024$1. --Low starting bid! Equipped with: 1st & 2nd Heads: Each with 2” W Cross brush belts, 2.5 kW (3.35 HP) - 1,690 RPM Motor, Rotating belt on vertical axis supports series of pads with abrasive paper, Pads are adjustable to vary angle of contact on panel during rotation of belt, Pads with abrasive strip makes contact with workpieces from both sides as it rotates. (3) 2” Dia. Rubberized hold-down rolls, (1) before and after each cross brush belt head. 3rd & 4th Heads: Each with 62” L x 16” Dia. Brush Roll & 2.5 kW (3.35 HP) - 1,140 RPM Motor, & Horizontal angle adjustment. 2-5/8” dia x 7/8” w swivel rubber wheels before each brush roll head. (1) 2” Dia. Rubberized hold-down roll after last brush roll head. 53-1/2” W x 12’ L Vacuum feed belt, with 2.64 kW (3-1/2 HP) - 1,695 RPM Motor, Holes on 1-1/2” W & 2” L Centers, 2-1/2” Dia. Rubber-covered infeed & outfeed rolls, Motorized adjustment with Digital readout with LED Display. Control motor load meters. Complete with: Instruction Manual.

Costa 60CT2-1150 (2)-Head, Wide Belt Sander44" width cap Drum, Combination HeadHead Co figuration 1st Head: Rubber-covered contact roll, 20 HP motor;2nd Head: Segmented polishing platen, (30) narrow segments are electronically controlled to conform to the panel shape and size to minimize veneer sand-throughs, each segment with variable pressure control, 15 HP motor.Specifications: -- Adjustable contact roll for varying thickness of abrasive belts with -- 45" x 103" Abrasive belt, electronic tracking. -- Motorized part thicknessopening on conveyor bed with digital readout, -- Variable feed speed 10 - 50 FPM with inverter drive, -- Vacuum conveyor bed assembly with 4 HP suction fan,infeed & outfeed spring loaded holddown rolls.Equipped with & Features: -- Controls mounted on the front of the machine, -- Instant shut-down safety guard, all motors with Y-Delta starters, and motor load meters.NOTE: Some spec's need to be verified

CP100 Can Flattener --220V, 1200 lbs per hour --Infeed Conveyor --Magnetic Separator -- New belt included

CP MANUFACTURING - S100-6-LH-US, ...Screens -- (1) System of (2) Screens -- Very lght Use -- Ordered as part of a Single-Stream Sort System that was designed to run 10 Tons/Hr -- 1-Feed Conveyor -- Each: 14,500 Lbs -- Loaded onto your Truck

CP CD1000 CAN DENSIFIER -- 900 to 1,500 Lbs/Hr capacity -- Fully automatic solid-state Controller -- Density: 40 Lbs per cu. ft. allowing 140,000 Lbs in 50' railcars or 40,000 Lbs in 40' Trailers. -- 10 HP - 3/60/208/230/460 Volt Hydraulic Power Unit

CAN-PAK - CD-3000: Complete Can Densifier -- Motor: 25 HP.Dimensions• Height: 9’-2";.• Width: 3’-10";.• Length: 13’-5";.• Machine weight: 8,000 Lbs.• Conveyor weight: 1,000 Lbs.• Conveyor: 11’-5"; High x 20-1/2"; wide x 13’ long.Specifications• 25 HP Power unit.• 460 Volt, 3-phase wiring.• Solid-state programmable controller.• Thermostatically controlled hydraulic oil cooler.• 1 Cubic yard hopper.• 120-gallon hydraulic tank.• 20-1/2"; Wide infeed conveyor with: 3/4 HP Motor. Direct drive gear reducer. Magnetic head pulley. Steel reject chute.

CRAFTSMAN DP-65 Drill PressSpecifications: -- Capacity: 15" -- Motor: 0.33 HP Equipped with: -- Push button control -- Stand

CRAM-A-LOT - HX-60: Closed Door Baler with Cart Dumper & Infeed ConveyorSpecifications: --The CRAM-A-LOT "HX-60 HH" & "HX" Series Balers are ideal for warehouses and designed for ease of installation, operation, and maintenance. -- CRAM-A-LOT® HH & HX Series Balers are: Built with extra Heavy-Duty construction; ideal for warehouses & recyclers who deal with large quantities of corrugated and paper products.Baler is designed for long hours of operation and can operate either manually or automatically with photocell control. Optional custom-engineered Feed Conveyors and Cart Dumper Systems efficiently control Baler feed rates for optimum performance in a complete Baling System.Standard Features include:ANSI Z245.5 Compliant: All Compactors meet or exceed ANSI Z245.5 safety standards.UL/CUL Listed Control Panels.UHMW Ram Shoes: Adjustable to assure straight tracking and readily replaceable, should the need arise.Oil Sight Gauge: Oil level at a glance.Oil Filter: Replaceable "spin-on" cartridge to keep your oil clean.Heavy-Duty Controls: NEMA 4-Rated pushbutton controls with "key lockable" start switch.Automatic single-cycle operation. -- Bale Size: 60" x 30" x 40". -- Bale Weight: Up to (OCC) 1,400 Lbs. --Throughput: (OCC) 2-1/2 Bales /Hr. -- Cylinder: 7".

CRAM-A-LOT - SCR-T2-34: (3) 34-Yard Self-Contained CompactorsNOTE: Lot of (3) Specifications: -- Cylinder: (2) 4". -- Main motor: 10 HP. -- Feed opening: 41″ x 58″ (1,041 mm x 1,473 mm). -- Capacity: 34-Yard. -- Ram force: Up to 24 tons.

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6k ROCKWELL/CRESCENT 5-Head Single Head Tenoner Equipped with: Manually-operated sliding table. (1) Top & (1) Bottom Tenon Heads, Each with 2 HP Motor, (1) Top & (1) Bottom Cope Heads, Each with 1 HP Motor, & (1) 7" Cutoff head with 1 HP Motor.

CROUCH - 81-70 ...Edge Sander (Non-Oscillating)5 HP Direct drive motor; 6" x 144" abrasive belt size; (1) 8" x 56" Platen.Equipped with: -- (1) 12" x 56" Adjustable side table and (1) 15" x 28" end table.Tables adjust vertically 5" and laterally 2-1/2". -- 8" Dia. rubber covered drive pulley and 4" dia. aluminum idle pulley.

CUMMINS - 682-FDR-036JJW, ...1000K DIESEL GENERATORSpecifications: -- Output: 480/277 / 3-Phase -- 1,000 kW -- 1,250 KVA -- 1,504 Amps -- 1,800 RPMNOTE: (299) Hours on meter in factory-built enclosure. - Available for inspection!

D M C - UNISAND 135, ...3-Head Wide Belt Veneer & Finishing Sander. -- General Data:3-Head, 51" (1,300 mm) nominal width cap.; motorized part thickness opening with LED readout; 1/8" to 4" max. - Head sequence: Cross belt, rubber-covered Drum, Pad. Head Configuration/Specs: -- 1st Head: Cross belt with: EPICS 44 Segmented electronically controlled air platen; 2-speed abrasive belt; approx. 36/72 FPM (11/22 MPS) linear speed; driven by 19 & 24 HP motors; 6" wide x 238" (6,050 mm) long abrasive belt. Inside synchronized Chevron belt, approx. 228" (5,800 mm) long.Pad unit with pneumatic cylinders: Each acting on a high absorption felt strip; working pressure controlled via control panel. HYDRA Belt: 2' Electronic control with oscillating blower for cleaning. -- 2nd Head: Rubber-covered 45-durometer steel roll, 9.8" (250 mm) dia. with: 18 HP 2-speed motor, 52" x 103" (4,055 mm) long oscillating abrasive belt with electronic tracking; air blast abrasive belt cleaner. Belt runs approx. 3,550 FPM (18 MPS) linear speed; adjustment & indicator of working position. -- 3rd Head: Flexible Sanding Platen with: EPICS 44 Segmented electronically controlled air platens; 3-speed 24 HP motors; 52" x 103" (4,055 MM) long abrasive oscillating belt with electronic tracking, timed oscillating air blast abrasive belt cleaner.Pad unit composed of: Pneumatic cylinders, each acting on a high absorption felt strip. Working pressure controlled vial control panel. Special rails allowing a quick change of graphite cloth on pad. Interchangeable system to modify the hardness, stiffness, and profile of the contact surface. Controller: -- DMC "HYDRA 30" Upgraded computer with: Working position display modes mounted in a separate control cabinet; automatic thickness device reads and adjusts feet table height, motor load meters. Transport Belt Drive: -- Variable feed speed of 16 to 82 FPM, conveyor feed drive, infeed & outfeed holddown pinch rolls on all heads; infeed hand safety stop, outfeed emergency stop; high efficiency dust extraction and separate control console with monitor, keypad, etc. Also included: -- Cleaning brush head at machine discharge. -- High pressure vacuum blower. -- Dust manifold. -- Extended outfeed table.

DMC - UNISAND 2000-M2, ...Wide Belt Sander (2) Heads -- 53" Width cap. Drum, Platen.Head Configuration: --1st Head: 11" dia. (300 mm) Rubber-Covered Contac; (2) speeds or inverter adjustable 20 - 25 HP; Varied RPM. --2nd Head: Combination head with drum and graphite covered 2-1/2" finishing platen; 25 HP.Specifications: -- 54"x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computor controlled; set-up functions with keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with: 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with: LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, motor load meters.2-Roll infeed conveyor extension; high efficiency dust extraction.

DMC - EuroSystem SY-TC 1350, ...Heavy-Duty 4-Head Wide Belt Sander53" Width cap. Drum, Drum, and Drum; Segmented Platen.Specification; -- Max. workpiece width: 53". -- Workpiece thickness: 0.32" - 6.8".Head Configuration & Feed: -- 1st Sanding Unit: 10"; Diameter grooved steel contact drum; 60 HP motor. -- 2nd Sanding Unit: 10"; Grooved rubber covered drum, 27 HP motor. -- 3rd Sanding Unit: 10"; Grooved rubber covered drum; 20 HP Motor. -- 4th Sanding Unit: Electronic segmented platen; 35 HP motor. -- Belt size of 53" x 103". -- Feed Motor: 5 HP, Variable feed speed. -- Vacuum Bed. -- Constant Pass Line.Equipped with & Features: -- Power Panel Touchscreen Control. -- Shoe type holddowns. -- Amp meters for all Sanding Units.

DMC - 1350 RK, ...TECHNOSAND Dual Head Wide Belt Sander.(2) Heads, 52" width cap. - Head sequence: Contact sanding roll and Segmented platen. Head Configuration:1st Head: 7" (175 mm) Dia., 85 durometer rubber-covered calibrating contact sanding roll.2nd Head: Segmented finishing platen with EPICS (sectional electronic pad) with (46) electronically controlled air segments.Specifications: -- 53" x 103" Long abrasive belts with electronic tracking on all wide belt heads. -- Turbo panel blowers, timed abrasive belt air cleaners. -- DMC "Hydra 35" control, "EPICS" control for sectional platens. -- (99) Programs; graphic screen for machine configuration, +/- control on segmented platens, abrasive belt cleaners. -- Sequential automatic start-up, machine troubleshooting and self-diagnosis. -- Variable feed speed from 15 - 60 FPM (4.5 - 18 MPM), 1.5 HP feed drive, vacuum conveyor bed with 7.5 HP suction fan and motor.Equipped with & Features: -- Automatic conveyor belt tracking, infeed & outfeed holddown pinch rolls or shoes on all heads. -- 0" - 4" Motorized programmable thickness adjustment with LED readout. -- Automatic part thickness adjustment, infeed hand safety stop, outfeed emergency stop. -- Motor load meters and control console with monitor & keypad.NOTE: Message from the Seller: The machine was setup by a DMC tech. It has a new calibration roller & new bearings, rebuilt HYDRA 35 controller; currently under power, comes with dust collecting manifold and hoses, plus the machine can be loaded onto a flatbed for ...$ 600.

DMC UNISAND K (3) Bottom and (3)Top heads wide belt sander. --, 43" max. width. - Bottom Head sequence : 1st Head Contact roll, approx.18.5 KW motor- 2nd Bottom Head Contact roll, 2rd Bottom head, Combination head with roll and platen , approx.15 KW 2-speed motor, belt speed 118 m/sec. -- Bottom panel brush. -- Top Heads: 1st Top Head: Rubber covered contact roll approx. 18.5 KW motor, 2 speed, belt speed 9/18 M/Sec. adjustable contact roll with pneumatic grit adjustment. 2nd and 3rd Top Head: Combination head with Rubber covered contact roll and polishing platen, approx. 18.5 KW HP motor, adjustable contact roll with pneumatic grit adjustment.Top panel brush. -- 44"x 103" abrasive belts with electronic tracking; computer controlled set-up functions with key pad and LCD screen. -- Vacuum Conveyor feed belt with variable feed speed from 11 - 60 FPM, approx. 7.5 KW HP feed drive, automatic conveyor belt tensioning & tracking. -- Infeed & outfeed holddown pinch rolls on all heads, motorized part thickness opening with LED readout, 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Complete with: Infeed safety stop, outfeed emergency stop, motor load meters, high efficiency dust extraction and control console with monitor. -- Actual model USK1350-IM3 + USK1350

SCM DMC 90 RCS 135 2 Head 53 inch Wide Belt Sander 53" Width cap, Steel Drum, Combination HeadHead configuration1st Head: Steel Drum 36 HP Motor, 9" Diameter 2nd Head: Combination head 65 shore drum and solid wood platen, 30 HP Motor, 7" Dia. drumSpecifications: -- 54" x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computer controlled; set-up functions with a keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, -- Motor load meters. -- 2-Roll infeed conveyor extension; -- High-efficiency dust extraction.NOTE: Specs have to be verified

DMC UNISAND K 1100 Wide belt sander4-Head, 43" (1,100 mm) max. width cap. Head sequence: (3) Contact rolls and (1) Combi with roller and segmented platen.Heads configuration: -- 1st Head: Helical grooved steel contact roll, 10" dia., 48 HP motor. -- 2nd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. and 65-Shore covering hardness, 35 HP motor. -- 3rd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. 45-Shore covering hardness, 30 HP motor. -- 4th Head: Combi head with roller covered with rubber, 30 shore and Finishing sanding pad unit , 30 HP 2-speed motor with segmented pads pneumatically controlled -- All heads use 44" x 103" (to be confirmed) abrasive belts and are equipped with electronic tracking, automatic tensioning, automatic emergency breaking, and oscillating sanding belt cleaners.Controls: -- "HYDRA V-PAD" 10" Touch-screen computer for setup functions, color LCD Display, allows operator to setup/recall part thickness, -- Conveyor feed speed (3.5 - 18 MPM), -- Abrasive belt direction, and reversible speed setting of 4th head. -- Conveyor belt feed with inverter control, feed speeds from 11 - 60 FPM, 5.5 HP feed drive; -- Infeed & outfeed holddown pinch rolls on all heads, automatic part thickness setup with the moving feed belt, -- 2-speed motorized part thickness adjustment, 1/8" - 6" max. opening; -- Infeed & outfeed motorized conveyor extension rollers, automatic part thickness setup sensor. Complete with: -- Safety stop at infeed, -- Anti-kickback device, -- Infeed & outfeed emergency stops, -- Motor load meters, i -- Infeed & outfeed idle rollers, -- High efficiency dust extraction, and control console with monitor.Note: (spare parts not installed) New feed belt , new front pressure roller, new front pressure bar and several new small parts for approx $15,000 of value +11 boxes (approx 5 belts/ box) sanding belts 100 grit, 120 grit, 180 grit and 220 grit.